567742

Velodyne Wi-Q10BV Manual

17
Zoom out
Zoom in
Previous page
1/29
Next page
17
Subwoofer Controls/Connections/Features Wi-Q User’s Manual
Low-Pass Crossover: Use this knob to select the frequency above which you wish to cut off the signal to
the subwoofer. When the knob is turned all the way to the left, the Subwoofer Direct feature is invoked and
the subwoofer plays all frequencies up to 135 Hz.
Low-pass Crossover - 40 to 135 Hz
The crossover control allows you to adjust the upper limit of the subwoofer’s frequency response
from 40 to 135 Hz. The subwoofer’s response begins rolling off above the frequency at which you
set this control. Set the crossover frequency to obtain a smooth and seamless transition from the
subwoofer to the main speakers in your system. The default crossover setting is 80 Hz. If your main
speakers are small with limited low frequency output, choose a higher frequency (such as 100 - 120
Hz). For larger speakers which have greater low frequency output, choose a lower number (such as
70 Hz).
Note: The subwoofer sums the left and right channels and passes the combined signal through
an adjustable low-pass crossover before sending it to the amplifier.
Subwoofer Direct
Use this setting on the low-pass crossover knob to allow frequencies up to 135 Hz into the
subwoofer. See the next section, Receiver/Processor Subwoofer Outputs for more about this feature.
Receiver/Processor Subwoofer Outputs
Your Velodyne subwoofer is designed to operate using the full-range audio signal for input when
using our built-in crossover. Many home theater processors/receivers (Dolby Digital™, DTS™,
THX™) have a “subwoofer out” jack (sometimes labeled “LFE”) that is internally filtered, settable at
the receiver/processor, and designed to be used with a powered subwoofer. In some installations, it
is beneficial to use BOTH the Velodyne crossover and the receiver/processor crossover, to achieve
a steeper crossover slope. In rare cases, combining an external crossover with the subwoofer’s
internal crossover may result in low output and increased noise. In these installations you may need
to bypass the crossover in either the processor or subwoofer, or simply set one crossover to a higher
frequency (such as 120 Hz) to restore maximum performance.
Alternate Connections
Your Wi-Q subwoofer uses modern 2.4 GHz wireless technology, so in most cases you can establish the
audio connection simply by connecting the transmitter to your audio receiver. In some situations, however,
you may need to connect RCA or speaker cables to your audio receiver. For these situations, your
subwoofer includes both line-level (RCA-type) and high-level (5-way binding post-type) connectors.
Note: Do not use both the RCA/Phono INPUT and SPEAKER LEVEL INPUT connections
simultaneously.
Line-Level Connections
Use the line-level jacks to connect your subwoofer to a pre-amp, a signal processor (with LFE out or
Sub-out), a line-level crossover, or a receiver with pre-amp level outputs. With line-level connections,
always use shielded phono cables, and to avoid potential noise problems, use the shortest cables
possible.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velodyne Wi-Q10BV at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velodyne Wi-Q10BV in the language / languages: English as an attachment in your email.

The manual is 4,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info