567837

Velodyne SC-8 Manual

17
Zoom out
Zoom in
Previous page
1/30
Next page
www.velodyne.com
SC-1250 Amplier User’s Manual - 11
A Word About Subwoofer Placement
Subwoofers operate at extremely low frequencies, which are primarily omni-directional. Keep in mind that
frequencyresponseandoutputlevelcanbedrasticallyinuencedbyplacement,dependingontheacoustic
properties of the listening room. Typically, the optimum location for a subwoofer is in a front corner of your
listeningroom.Thislocationwillusuallyoerthegreatestoutputlevelsandoptimumlowfrequencyextension.
The worst location for a subwoofer is typically far away from any walls, close to the center of your room and near
an opening or doorway. Avoid these locations when possible. When using a pair of SC subwoofers in stereo, it
is preferable to place each subwoofer by the satellite of the same channel. Typically, a minimum distance of one
to two feet from your TV to the subwoofer will be adequate to avoid any magnetic interference.
Remember that the built-in 7 band EQ will help to get the most performance out of your subwoofer no matter
where it is placed.
Caution!
This amplier has electronics built into the cabinet. Do not place the amplier next to sources of heat such as
furnace registers, radiators, etc. Likewise, do not place the amplier near sources of excessive moisture, such as
evaporative coolers, humidiers, etc. The power cord should be routed in such a way that it will not be walked
on, pinched or compressed in any way that could result in damaging the insulation or wire.
SELECTING THE SUBWOOFER(S) TO BE CONTROLLED
Your SC-1250 can control a variety of Velodyne SubContractor Series subwoofers as well as generic passive
subwoofers.Specialinternalsoftwaresettingsaredesignedtomaximizeperformanceandreliabilitydepending
on the model of subwoofer being controlled, so it is important to match the SC-1250 amplier with the
subwoofer(s) it is controlling. The SC-1250 comes with a default setting for the SC-10 subwoofer. When the
unitisrstpoweredup,themodelbeingcontrolledisdisplayedfor2secondsonthenumericLEDbeforethe
display reverts to the volume setting. The subwoofer to be controlled is shown as follows:
** - The generic subwoofer setting is for passive subwoofers not on the above list. CAUTION: there is no anticlipping or anti-
distortion protection on this setting.
Tochangethesubwoofertobecontrolled,rstpowerdowntheamplierusingthepowerswitchontheback
panel (DO NOT use the power button on the front panel). Then, turn the switch on while depressing any of the
buttons on the front panel (crossover up or down, or volume up or down). The unit will show the model it is
currently controlling. To change the model, simply push the crossover up or crossover down buttons and the
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velodyne SC-8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velodyne SC-8 in the language / languages: English as an attachment in your email.

The manual is 1,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info