567740
14
Zoom out
Zoom in
Previous page
1/28
Next page
www.velodyne.com
8 - Optimum Series User’s Manual
Following are brief descriptions of the connections described in Figure 2. More detail on these connections can
be found in the next section.
(1) LOW-PASS CROSSOVER
Use this knob to select the frequency above which you wish to roll o the signal to the subwoofer. When
the knob is turned all the way to the left, the Subwoofer Direct feature is invoked and the subwoofer
plays all frequencies up to 200 Hz.
(2) VOLUME Control
This control allows you to balance the output from the subwoofer to the main speakers in your system.
This control should be set to achieve similar volume level from between both the main speakers and
subwoofer. When pressing volume up or down, set the level while watching the LED display for reference.
The upper button increases the subwoofer level and the lower button decreases it.
Note: Volume is also controllable by using the supplied remote. When defaults are restored, the default
volume setting is 30 out of 80.
(3) AUTO ON/OFF Switch
Use this switch to select between auto-on (active) and constant on (auto-on inactive) operation.
(4) LINE OUTPUT
Connect these jacks to the LINE IN amp input to use the Optimum subwoofer’s internal high pass
crossover. See below for a more detailed explanation of this crossover.
(5) LINE INPUT/LFE Input
Connect these jacks to the LINE OUT preamp output, LFE output or subwoofer output jacks of your
receiver/processor. If using the LFE output from your receiver or processor, plug the single cable into the
“L” - LFE input or for more signal, use a “Y” connector (not included) and feed the signal into both “R”
and “L” inputs.
(6) SPEAKER LEVEL INPUT Terminals
Connect these input terminals to the speaker output terminals of your amplier or receiver. If you use
this method of connection, when you go to the receiver speaker set up menu, make sure you select the
large speaker option.
(7) IR Input
This is a connection that allows the utlization of a third party infrared remote sensor, such as Elan or
Xantech, or an extended cable for placement closer to your other remote controlled equipment. This
keeps you from awkward control angles using the infrared remote control.
(8) 12v Trigger
When this 2-conductor mini jack is connected, the amplier remains in power-o mode until the trigger
is applied. The correct trigger is +12V on the tip of the connector relative to the grounded sleeve.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velodyne Optimum-12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velodyne Optimum-12 in the language / languages: English as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Velodyne Optimum-12

Velodyne Optimum-12 Additional guide - English - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info