567711
9
Zoom out
Zoom in
Previous page
1/42
Next page
CONTROLS & CONNECTIONS
T
he subwoofer is set up, configured and adjusted by the controls, inputs and connections located on the back and front panels of the
subwoofer and the remote. Figures 1, 2 and 3 show the location of each of these important operational interfaces. Brief descriptions of each
i
nterface are below.
Cabinet Front
I
n order to access the controls and connections on the front of the cabinet, you need to remove the grille. You don’t need to remove the grille
right now. For instructions on how to remove and re-install the grille, see the Remove Subwoofer Grille and Install Subwoofer Grille sections.
Figure 1: Subwoofer Cabinet Front with Grille Removed
REMOVE SUBWOOFER GRILLE
To remove the grille:
1. Place your thumbs on the top outside corners of the grille.
2. Use your thumbs to gently apply downward pressure to the top outer grille edges and pull the top grille edge towards you.
3. After the top of the grille is free of the top cabinet face, carefully rock the bottom grille cups of the grille off of the steel grille pegs.
INSTALL SUBWOOFER GRILLE
To reinstall the grille:
1. Carefully insert the bottom grille cups of the grille onto the lower steel grille pins.
2. Place your thumbs on the top outside corners of the grille.
3. Use your thumbs to gently push the top grille onto the cabinet face.
4. Push the grille to the cabinet over each grille pin.
[ 6 ]
D
igital Drive
P
LUS
U
ser’s Manual
PART ONE — OPERATE
A. USB: Connect this mini USB to a
PC to optionally use the Windows
Setup Program to optimize the
subwoofer output.
B. MIC: Connect the smaller end of the
mic cable to use the microphone in
conjunction with the Sweep Tone CD.
The EQ functions will terminate unless
the microphone is connected.
C. Remote Control Sensor: Receives
remote control commands.
D. LED Display: Shows volume level,
crossover frequency and Auto-EQ
P
LUS
status messages. LED display is
visible through the front grille.
E. VOLUME: Adjust subwoofer output
volume.
The volume level shows
on the LED.
F. CROSSOVER: Adjust low pass
crossover frequency. The crossover
frequency shows on the LED.
G. AUTO EQ: Press and hold for 5
seconds to start the Auto-EQ
PLUS
function. This time delay prevents
accidentally performing the
Auto-EQ
PLUS
function. “AU”
appears on the LED display
once Auto-EQ
PLUS
starts.
The volume and crossover frequency return to their saved values after a power cycle unless these settings were
saved using the Auto-EQ
PLUS
software’s TV screen or PC interface. The volume and crossover knobs don’t change
settings during Self-EQ,
Auto-EQ or Manual-EQ.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velodyne DD-18plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velodyne DD-18plus in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Velodyne DD-18plus

Velodyne DD-18plus Quick start guide - English - 2 pages

Velodyne DD-18plus User Manual - English - 40 pages

Velodyne DD-18plus Quick start guide - German - 2 pages

Velodyne DD-18plus User Manual - German - 20 pages

Velodyne DD-18plus User Manual - German - 36 pages

Velodyne DD-18plus Quick start guide - French - 2 pages

Velodyne DD-18plus User Manual - French - 47 pages

Velodyne DD-18plus User Manual - French - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info