622813
3
Zoom out
Zoom in
Previous page
1/16
Next page
The 3D printer contains a lot of moving parts, but the force of the stepper motors is too low to cause serious injuries. Never-
theless it is recommended to provide additional protection against mechanical risks.
The easiest way to make your 3D printer “accident proof” is to put it inside a protective enclosure which completely covers
the 3D printer – with or without an access door and fume extraction. (numerous designs can be found on the internet)
To make it extra safe a switch which interrupts the power supply of the printer when the enclosure or door is opened can be
added. It is also advisable to install an external emergency stop switch, which also cuts off the power supply.
Providing adequate protection is the responsibility of the assembler.
Always cut power before maintenance or modication.
Mechanical safety and protection:
!
The 3D printer is not intended for use by persons (including children) with reduced physical, or mental capabilities,
or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of
the appliance by a person responsible for their safety
Children should be supervised to ensure that they do not play with the appliance.
The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide.
The information in this document was obtained from sources which we believe are reliable.
However, the information is provided without any warranty, express or implied, regarding its correctness.
The conditions or methods used for assembling, handing, storage, use or disposal of the device are beyond our control and
may be beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability
for loss, injuries, damage, or expense arising out of or in any way connected with the assembly, handling, storage, use or
disposal of the product.
General safety information:
There is a potential risk of burns as the Printer head (extruder) can reach up to 270°C.
The use of common sense should be sufcient to prevent burns, but in some environments it is highly recommended to
provide additional protection. (see § Mechanical safety and protection)
The max. temperature of the heated bed is 60°C, this is below the 1 min. burn threshold for plastic surfaces according to
CENELEC Guide 29. Normal reexes prevent long contact periods with hot surfaces
Always let the 3D printer cool down for 60 min. before maintenance or modication.
Risk of burns:
!
This printer is designed for use with PLA and ABS lament (MSDS for the Velleman lament is available).
PLA: is a safe and non-toxic material, there are no known health safety risks when used in 3D printers.
ABS: when printing with ABS there is a distinctive ‘burned plastic’ smell. This is quite normal but it may also cause head-
aches, respiratory- and eye irritation with sensitive people (although it is not toxic)
Only use the printer in a well-ventilated area, if printing with ABS it is advisable to add a fume hood (with active car-
bon ltering for ductless extraction). Fume extraction is mandatory for use in ofces, classrooms and alike.
Never burn printer lament, toxic gasses and vapors will be generated if exposed to re.
Health:
!
- 3 -- 2 -
������������������ ��������������������
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velleman K8200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velleman K8200 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 2,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Velleman K8200

Velleman K8200 User Manual - English - 25 pages

Velleman K8200 Installation Guide - German - 664 pages

Velleman K8200 Installation Guide - Dutch - 3 pages

Velleman K8200 User Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info