622291
48
Zoom out
Zoom in
Previous page
1/67
Next page
circuito a prueba.
Conecte la punta de prueba roja al borne « VΩ Hz » y la punta de prueba
negra al borne « COM ».
Seleccione el rango « Hz ».
Pulse la tecla « RANGE » para seleccionar el rango.
Conecte las puntas de prueba al circuito. El valor medido se visualiza.
Nota:
o Es posible medir la frecuencia durante la medición de una corriente o una
tensión CA. Efectúe la medición y pulse la tecla « Hz% ».
o Utilice cables blindados para medir señales débiles en un ambiente ruidoso.
7.7 Medir la temperatura
No toque el circuito bajo tensión con la sonda térmica
Seleccione el rango « °C ». la temperatura ambiente se visualiza si la sonda
térmica no está conectada.
Introduzca el adaptador en las entradas « VΩ Hz » y « COM » (alinee + y VΩ
Hz ).
Introduzca el termopar en el adaptador (alinee + y +).
Mantenga la sonda contra el objeto que quiere medir
El valor medido se visualiza.
7.8 Medir la corriente
No mida una corriente de un circuito con una tensión > 1000 V.
Para corrientes hasta 600 ma, utilice el borne « µAmA ».
Para corrientes hasta 10 A, utilice el borne « 10A ».
Sea extremadamente cuidadoso al medir una tensión > 60 VCC o 30 VCA
RMS. ¡Ponga siempre sus dedos detrás de la barrera de protección!!
Para mediciones hasta 600 mA: Introduzca la punta de prueba roja en el borne
« µAmA » y la punta de prueba negra en el borne « COM ».
Para mediciones hasta 10 A: Introduzca la punta de prueba roja en el borne
« 10A » y la punta de prueba negra en el borne « COM ».
Seleccione el rango « µA » para mediciones hasta 600 µA (sólo si la punta de
prueba está introducida en el borne « µAmA »).
Seleccione el rango « mA » para mediciones hasta 600 mA (sólo si la punta de
prueba está introducida en el borne « µAmA »).
Seleccione el rango « A » para mediciones hasta 10 A (sólo si la punta de prueba
está introducida en el borne « 10A »).
Pulse la tecla « SELECT » para seleccionar el rango de corriente CC (DCA) o CA
(ACA).
Conecte las puntas de prueba en serie al circuito.
El valor medido se visualiza.
Nota :
o El valor visualizado para una medición de corriente CC va precedido por « - » si
está presente una polaridad negativa en la punta de prueba roja.
o El rango « µAmA » está protegido contra las corrientes excesivas por un fusible
F630 mA, 1000 V; el rango « 10A » está protegido contra las corrientes
excesivas por un fusible F10 A, 1000 V.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Velleman DVM4100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Velleman DVM4100 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info