578346
25
Zoom out
Zoom in
Previous page
1/65
Next page
16
EN
to the ground
step 2 Mark this point on the ground with a line (use chalk for
example)
step 3 Push the bike one wheel rotation forward until the valve is
again vertical to the ground.
step 4 Mark this point on the ground as well.
step 5 Measure the distance between the two marks. The result is
your wheel circumference (=roll circumference).
step 6 Enter the wheel circumference as described below into your
VDO computer.
ATTENTION: If you have selected KMH display then you must enter the
wheel circumference in mm. If you have selected MPH display then
enter the wheel circumference in inches. The values listed in table
>>>
P10 are approximate values. These values deviate depending on brand
of tire, tire height and tire tread.
Setting wheelsize:
3 sec. ç Setting mode LANGUAGE SELECT
ƒ WHEELSIZE SET
WHEELSIZE KMH-DISPLAY or WHEELSIZE MPH-
DISPLAY ( to change to mph)
WHEELSIZE 1 … SET SIZE ?CONTINUE?
ƒ Set wheel size 1 in mm (keep button depressed for
fast run-through)
WHEELSIZE 1 ?SET OK?
WHEELSIZE 1 SET DONE
Automatic change to
ƒ Set wheel size 2 in mm (keep button depressed for
fast run-through)
WHEELSIZE 2 ?SET OK?
WHEELSIZE 2 SET DONE
Automatic return to operation mode for TRIP DIST. If you do not want to
set wheel size 2 then hold å to return to TRIP DIST operation mode.
Attention: Factory settings for bike 1 = 2155 mm and for bike 2 =
2000 mm. If you do not enter wheel sizes the computer will work with
the factory settings. The values measured in this manner for speed,
distance, etc. can deviate from the actual values.
5.2. CHANGING THE WHEEL SIZE
With wheel size you change the computer from bike 1 (e.g. road bike)
to bike 2 (e.g. mountain bike). The computer now works with the
settings for bike 2.
3 sec. ç Setting mode LANGUAGE SELECT
ƒ WHEELSIZE CHANGE
ƒ WHEELSIZE 1 or WHEELSIZE 2 ?SET OK?
ƒ Changing the wheel size
WHEELSIZE SET DONE
Automatic return to TRIP DIST
Wheel size set done
Display of the actual wheel size in the center bar of the display, right
bottom (1 or 2)
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VDO Z3 PC-Link at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VDO Z3 PC-Link in the language / languages: English as an attachment in your email.

The manual is 0,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of VDO Z3 PC-Link

VDO Z3 PC-Link User Manual - German - 65 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info