484614
8
Zoom out
Zoom in
Previous page
1/19
Next page
8
* Depending on version
CLOCK *
This set has a clock that can either be manually
set by you or can be automatically updated via
the RDS signal.
SETTING THE CLOCK (MANUALLY)
Enter the Initial Settings menu.
Select option 'CLK'.
Alter the Choice to 'MAN'.
,
Display shows e.g. '00:00' (24 hour format) or
'AM 12:00' (12 hour format).
To adjust the Clock
The clock starts operating from the selected
time.
Leave the Initial Settings menu :
10 seconds after any key operation, the display will
always show the time when clock mode is activated.
RDS CLOCK * (AUTO UPDATED)
You can select an automatic update of the clock
via the RDS radio signal.
See INITIAL SETTINGS; select Option 'CLK'
and set Choice to 'AUTO'.
The transmitted time via RDS can be incorrect.
SDVC (SPEED DEPENDENT VOLUME
CONTROL) AND SPEED WARNING
See INSTALLATION for connection instructions.
SDVC *
To compensate for surrounding noise this function
automatically increases the volume of the set as
a result of the car's speed. Four compensation
levels can be selected. Level 1 gives a small
increase up to level 4 which gives a greater
increase. See 'INITIAL SETTINGS' option SDVC
to alter the level until you find one which suits
your car.
Speed Warning *
You can use this function to inform you that you
are exceeding a certain speed. Always obey
the Highway Code and current traffic
restrictions and conditions!
To calibrate :
To avoid unnecessary distraction we advise
that this procedure is carried out with the
help of somebody else.
1 While stationary, hold down the 'SPEED' key
turn on the set.
2 The set mutes. Display shows 'CALIBRAT' and
then '50 KM/H'.
3 Now drive to 50KM/H (30MPH)
(Always obey the Highway Code and
current traffic restrictions and conditions!)
4 Once 50KM/H (30MPH) is reached briefly press
'SPEED' key :
You hear a beep and display shows 'CALIB
OK' and then 'SDVC ON'.
5 Now turn the set off and on again to return to
normal operation.
Level 3 is chosen for 'SDVC' and 'SPD' is set to
KM/H in 'INITIAL SETTINGS'.
SPECIAL FUNCTIONS
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VDO Dayton CR 2101 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VDO Dayton CR 2101 in the language / languages: English as an attachment in your email.

The manual is 1,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info