7270

VDO Dayton CD 2803 Manual

7
Zoom out
Zoom in
Previous page
1/16
Next page
7
* Depending on version
Infrared remote control
You can use a VDO Dayton infrared remote control
with this set. Please consult your dealer for the
correct infrared remote control.
MOUNTING
METAL SLEEVE (fig. 10)
• Install the metal sleeve (dimension 182x53 mm)
in the dashboard. For optimal performance of
the CD player, the metal sleeve should be
positioned horizontally (between -10
o
and +30
o
).
• Fix metal sleeve into place by pressing the metal
tags outwards using a screwdriver.
CONNECTING THE RADIO (fig. 9)
• Ensure the battery is disconnected.
• Insert aerial plug E into aerial socket (good
reception is only possible with a good aerial).
Fix antenna adaptor if needed. Use hook (J) on
back of set to secure fixing.
• Insert power supply connector A into socket A’.
• Insert loudspeaker connector B into socket B’.
• (optional) Remove the protective cover from
socket C’.
• (optional) Insert the yellow line-out connector
C1 into socket C1’.
• (optional) Insert the blue CD changer connector
C3 into socket C3’.
• (optional) Insert the green connector C2 into
socket C2’.
The green connector slides between the yellow
connector C1 and the blue connector C3.
You need at least one of these connections to
keep C2 in place.
MOUNTING RADIO
This radio can be properly installed either from
conventional Front Mounting or Rear Mounting.
FRONT MOUNTING
• Slide the radio into the metal sleeve until the
springs at either side of the radio snap into the
openings of the sleeve (fig. 11).
• Finally reconnect the negative car battery
terminal (fig. 12).
REMOVING RADIO (using the two U- brackets
supplied)
• Remove the trimplate around the front panel.
• Insert both U-brackets into the holes on the front
of the set until they lock. Pull out the radio (fig.
13).
REAR MOUNTING (fig. 14)
• Remove the trimplate around the front panel and
the side springs.
• Select a position where the screw holes of the
mounting bracket and the screw holes of the
radio become aligned and tighten the screws at
2 places on each side.
• Only use M5 screws that are not longer than
6mm.
REPLACING FUSE (fig. 9)
• Replace with a 10A blade-type fuse. The new
fuse must be of exactly this value and type
otherwise the set will not be adequately
protected. Ignoring this procedure may lead to
damage to the set, which will invalidate the
guarantee.
INTERFERENCE SUPPRESSION
• Most modern cars have sufficient interference
suppression. If you experience interference
generated by the car, consult your garage.
004-16 Mid_Eng 8/15/02, 6:48 PM7
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VDO Dayton CD 2803 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VDO Dayton CD 2803 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info