163607
6
Zoom out
Zoom in
Previous page
1/16
Next page
6
This can only be accomplished by
persons familiar with automotive
electrical and mechanical systems.
After Connection, see "SPECIAL FUNCTIONS'
for calibration procedure.
Electronic antenna/Motorised antenna
:
Connect pin A5 to the power supply for an
electronic antenna or the control wire for the
relay of an automatic motorised antenna. Use
the small connector supplied.
Do not use this connection for the supply
lead of the aerial motor!
Pilot light
:
CONNECTOR B** (fig. 3)
Loudspeakers (use 4 ohm loudspeakers only)
Do not connect any of the loudspeaker leads to
earth or directly to a booster/amplifier without
high level input or via an external fader! You can
connect the loudspeaker leads directly to an
amplifier with high level input.
Connecting 4 loudspeakers:
Front Rear
Left+ Green [B5] White [B7]
Left- Green/black [B6] White/black [B8]
Right+ Grey [B3] Blue [B1]
Right- Grey/black [B4] Blue/black [B2]
CONNECTOR C
1
Yellow Connector C1 for Pre-out* (fig. 4)
Connect a power amplifier (with 4 addi-
tional loudspeaker) to this set with the RCA
cable.
Connect Red socket to Right channel and white
socket to Left channel.
Connect Blue wire to Amplifier Remote on/off.
Green connector C2 (fig. 5)
Steering wheel remote control
You can connect certain car steering wheel
mounted remote control to this set via an interface.
Please consult your dealer for the correct interface.
If your car telephone or the car kit of your mobile
phone provides a mute signal, it can be used to
automatically interrupt the set's sound output.
Connect the telephone mute wire to the
connector D1.
See 'SETUP' select option 'TEL' and set 'MUTE
LO' or 'MUTE HI' (according to phone type) to
automatically interrupt the set's sound output
when using your car phone.
** For this accessory, see your dealer
* Depending on version
OTHERS CONNECTIONS
Telphone mute (fig.8, fig.9)
External Remote Display (fig.7)
You can show the content of headunit on a
specific car remot display via connector D3.
Contact your dealer for an ' EDI Box ' of the
specific car which is sold separately.
When the car headlights are switched on, the
backlight of all headunit key buttons will be
illuminated
(even when the headunit is switched off).
Connect pin A6 to the dashboard illumination
wiring of the car.
Note : In certain car (e.g. VW Passat) the
dashboard illumination is dimmed by a digitally
modulated signal (PWM - Pulse Width
Modulation). This PWM signal can disturb the
illumination display of the car radio. In this
case, connect pin A6 to the switch signal of
the low beam headlight. Please consult your
car dealers for more information.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VDO Dayton cd 2304 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VDO Dayton cd 2304 in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,79 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info