34241
2
Zoom out
Zoom in
Previous page
1/3
Next page
5. Programming of computer
To show Speed and calculate Trip Distance and the other data, your VDO A8 needs the precise wheelsize = wheel circumference
(in mm or inch) of your bike.
5.1 HOW TO DETERMINE YOUR WHEELSIZE:
The wheelsize setting can be done with an accuracy of 1 mm or 0.1 inch.
The table below shows the most common tire sizes and the related wheelsize-data in mm and inch.
This data not necessarily corresponds with the correct data of your bike.
If your Tyre Size is not shown in the Table, you can find your correct wheelsize as explained below:
STEP 1 Stand your bicycle upright. With your tyre inflated to its proper pressure, rotate your front wheel so that the valve is located at
the bottom (6 o’clock position). Make a mark on the floor to indicate the valve location.
STEP 2 Roll the bicycle forward in a straight line for one complete wheel revolution, until the valve is again at the bottom. Make a
mark on the floor to indicate this valve location.
STEP 3 Measure the distance between the marks in millimetres or inches (1 inch = 25.4mm). This value is your wheel size = wheel
circumference.
5.2 SELECTION OF km OR m-READING
The VDO A8 can show speed and all related data either in km or Miles. You can switch at any time from km to m-reading
and vice versa. All data TRP, AVS, MXS, ODO will automatically be re-calculated.
STEP 1 Get TRP in display, press and hold SET-button for 3 sec.
STEP 2 km or m are flashing. Use MODE-button to select km or m-reading.
STEP 3 Press SET-button to confirm above selection. The A8 will now show the set-mode for the wheelsize = wheel
circumference.
5.3 PROGRAMMING THE WHEELSIZE
After pressing SET-button to confirm km or m selection, the A8 will now show the set-mode for the wheelsize = wheel circumference.
Factory settings for wheelsize are 2155 mm for km-reading and 84, 8 inch for m-reading.
Attention: For km-reading the wheelsize needs to be set in mm, for m-reading the wheelsize needs to be set in inches.
STEP 1 Change the flashing wheelsize-digit to requested value by pressing the MODE-button.
STEP 2 Press SET-button to confirm this setting and move to next digit.
STEP 3 Repeat Step 1 and Step 2 until all digits have been set to your wheelsize.
STEP 4 Press and Hold SET-button for 3 sec. to finish Wheelsize-Setting and return to TRP-display.
5.4 CLOCK SETTING
Your VDO A8 shows actual time in 24:00 (hh:mm) format.
STEP 1 Get CLK into display. Press and Hold SET-button for 3 sec. The Clock SET-Mode will be shown in display.
STEP 2 Use the MODE-button to change the flashing hour-digits. Hold MODE-button for fast setting.
Confirm your settings by pressing the SET-button. This confirmation will also change to Minute-setting.
STEP 3 Use the MODE-button to change the flashing Minute- digits. Hold MODE-button for fast setting.
STEP 4 Press and hold SET-button for 3 sec. to finish Clock-Setting and return to CLK-display.
5.5 PROGRAMMING OF ODOMETER
The total distance counter ODO can be programmed anytime, for example after a change of battery or to enter the ODO data of your old
computer into your new A8.
STEP 1 Get ODO into display, press and Hold SET-button for 3 sec. The ODO-Set-Mode will be shown in display.
STEP 2 Press MODE-button to change the flashing digit to requested value.
Confirm this setting by pressing the SET-button and simultaneously change to next digit (flashing).
STEP 3 Repeat STEP 1 and STEP 2 until all digits have been set to requested value.
STEP 4 Press and Hold SET-button for 3 sec. to finish ODO-setting and return to ODO-display.
P06
P07
P07
P08
P09
WS in mm / inch
1x
P05
CYCLECOMPUTING
Instruction manual A8
GB
Tire size WS in mm KMH WS in inch MPH
47-305 16x1,75 1272 50,1
47-406 20x1,75 1590 62,6
34-540 24x1 3/8 1948 76,7
47-507 24x1,75 1907 75,1
23-571 26x1 1973 77,7
40-559 26x1,5 2026 79,8
44-559 26x1,6 2051 80,7
47-559 26x1,75 2055 80,9
50-559 26x1,9 2060 81,1
n/a 26 x 1,95 2070 81,5
54-559 26x2,00 2075 81,7
n/a 26 x 2,1 2080 81,9
57-559 26x2,125 2133 84,0
37-590 26x1 3/8 2105 82,9
Tire size WS in mm KMH WS in inch MPH
20-571 26x3/4 1954 76,9
32-630 27x1 1/4 2199 86,6
40-622 28x1,5 2224 87,6
47-622 28x1,75 2268 89,3
40-635 28x1 1/2 2265 89,2
37-622 28x1 3/8 2205 86,8
18-622 700x18C 2102 82,8
20-622 700x20C 2114 83,2
23-622 700x23C 2133 84,0
25-622 700x25C 2146 84,5
28-622 700x28C 2149 84,6
32-622 700x32C 2174 85,6
37-622 700x37C 2205 86,8
40-622 700x40C 2224 87,6
F
P05
F
P06
F
P07
!
MINIMUM WS: 100 mm / 3,94“
MAXIMUM WS: 3999 mm / 157,44“
F
P08
F
P09
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VDO A8+ at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VDO A8+ in the language / languages: English as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of VDO A8+

VDO A8+ User Manual - English - 2 pages

VDO A8+ User Manual - English - 3 pages

VDO A8+ User Manual - German, Dutch, Danish, French, Italian, Portuguese, Spanish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info