540858

VAX Power 2 Manual

8
Zoom out
Zoom in
Previous page
1/12
Next page
8
maintenance
Remove the height adjuster knob from the top of the
floor head cover. Remove the floor head cover, lifting
from the rear of the machine (Fig.7/3).
Lift the right side of the brushbar and lift the left hand
side and remove the brushbar from the floor head
(Fig.7/4).
Remove the worn or broken belt from the motor drive
shaft.
Carefully remove any belt residue that may exist in the
belt area before replacing with a new belt.
Loop the new belt first over the motor drive shaft and
then over the agitator pulley.
Insert the right side of the brushbar in first by placing the
end cap down in the slot and then so the same with the
left side. Press firmly to make sure that each end is
completely inserted.
Check to make sure that the belt is centred on the
agitator pulley and that the brushbar turns.
Replace the floor head cover then reattach the carpet
height adjuster knob. Secure parts by screwing in one (1)
screw underneath the small wheel flap and the five (5)
screws on the underside of the vacuum cleaner.
8. Clearing Blockages
WARNING : To reduce the risk of electric shock, the
power cord must be disconnected before
performing maintenance/ troubleshooting checks.
Turn the vacuum cleaner off and unplug from the
electrical outlet.
Hose Blockages
The flexible hose may be disconnected from the vacuum
cleaner. Carefully remove any blockages found and
reconnect hose securely.
Accessory Blockages
Remove accessory from hose/extension wand. Carefully
remove the blockage and return to the cleaner.
Clearing debris from the TurboTool (some models
only)
1. Turn the TurboTool over and slide off the O-ring
(Fig.8/1).
2. Pivot lowering housing and remove clog (Fig.8/2).
3. To re-assemble, be sure that the tabs are engaged.
Pivot the lower housing closed. Slip the O-ring into the
groove at the neck of the TurboTool to complete
reassembly (Fig.8/3).
vax.co.uk
Fig.7/3
Fig.7/4
!
Fig.8/1
Fig.8/2
O-ring
U89 U90 & U91-P2 Power 2 Series User Guide V2.0:U90-P2 User Guide 13/08/2010 11:44 Page 8
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for VAX Power 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of VAX Power 2 in the language / languages: English as an attachment in your email.

The manual is 1,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info