756792
8
Zoom out
Zoom in
Previous page
1/21
Next page
POWXG6310 EN
Copyright © 2020 VARO Page | 8 www.varo.com
flashes this will indicate that wire loop is interrupted, and then mower will not
work.
7.3 Charging the lawnmower
Your robotic lawnmower´s battery may be charged to a certain degree on delivery, but it´s
recommended to fully charge the battery of the lawnmower before use. To charge your robotic
lawnmower follow these steps:
1. Switch the robotic lawnmower on. The On/Off switch (6) is located at the bottom
side of the robotic lawnmower (FIG A and Fig 2).
Note: Your robotic lawnmower will not charge when it is not turned on.
Note: The robotic lawnmower will enter a self-checking state (normally within
5 seconds) after entering the password or when the power is interrupted
during mowing or charging (indicated by a flashing status light). If the mower
is in a self-check state, you will not hear a sound when pressing a button and
the buttons won´t work.
2. Slide the robotic lawnmower into the charging station to charge.
3. Check the indicator on the charging station. The red power light turns up and the
robotic lawnmower charges (green light flashes). If the power light does not light up,
you should check the mains plug of the power supply is plugged in properly and that
the mower is in the station correctly.
4. It takes about 180 minutes to get the battery fully loaded.
7.4 Setting up the perimeter wire (Fig 3, Fig 4 and Fig 5)
The wire defines the borders of the mowing area. Everything in the inner area belongs to the
mowing area, everything in the outer area doesn´t belong to the mowing area. The wire also
serves to mark obstacles and exclude them from the mowing area.
1. Feed the end of the perimeter wire through the groove on the front at the bottom
side of the charging station, until it appears on the rear side (Fig 3).
2. Carefully strip off 10-15 mm of the insulation of the wire.
Note: You should keep a length of 15-20 cm at start and the end of the wire for
operating and handling the wire.
3. Connect the wire to the right hand (black) B terminal of the charging station (Fig 4).
4. Start installing the perimeter wire from the charging station in a clockwise direction
(Fig 5). Pull the wire from the coil, tauten and fix it with one peg. Use a mallet to
insert them in the lawn. Ensure the wire is straight and in line with the charging
station groove for 1.5 m.
5. Recommended distance between pegs is 50 to 75 cm (max).
6. Continue to set the wire around the perimeter of the mowing area.
7. For a more accurate perimeter, we advise that you leave less than 75 cm between
pegs when wiring objects (like flower beds, bushes, trees and other items).
Loose wire can be cut during mowing. Make sure the wire is flat to the ground.
Use additional pegs where the wire is slack. The wire is taut before placing the
next peg (if you can place a couple of fingers under the wire this is not taut
enough). Increase the number of pegs at a corner.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo POWXG6310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo POWXG6310 in the language / languages: English as an attachment in your email.

The manual is 0,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo POWXG6310

Varo POWXG6310 User Manual - German - 22 pages

Varo POWXG6310 User Manual - Dutch - 22 pages

Varo POWXG6310 User Manual - French - 23 pages

Varo POWXG6310 Additional guide - All languages - 7 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info