581889
12
Zoom out
Zoom in
Previous page
1/16
Next page
POWXG6026 EN
Copyright © 2014 VARO P a g e | 12 www.varo.com
All protective covers of the lawn mower and the power unit.
The aforementioned parts must always be replaced by spare parts authorised by the
manufacturer or by equivalent spare parts. Please contact your local dealer about this.
12.2 Replacing the blade
WARNING: Do not lift the lawn mower, while the blade is still running. Wait,
until the device comes to a complete standstill. Before doing any service
works, remove the spark plug connector from the spark plug.
After assembly of the blade, turn the lawn mower to its normal working
position (blade unit facing to the ground). Attach the spark plug connector
to the spark plug, and perform a test run of the engine. In case of unusual
vibrations, please contact your local dealer. Do not start the lawn mower in
a tilted position.
As regards to safety, the cutting blade is deemed to be a critical item. Therefore only cutting
blades marked with the label "DAYEE DY0608-12" can be used.
To remove the blade: remove the screw, check the blade holder for proper function, and
replace any worn or damaged parts.
Before installing the blade again, check that the cutting edges are properly aligned to the
rotation direction of the engine. The blade screw must be fixed with an electrodynamic tool
with a tightening torque of 3.7 kg/m (37 Nm).
THE BLADE: The blade is made of pressed steel. To ensure efficient working results, sharpen
the blade in regular intervals, around every 25 working hours. Make sure the blade is being
sharpened evenly. Insert a small metal angle (metal edge profile) (φ2 or φ3 mm) into the
centre orifice of the blade. The blade must be aligned horizontally.
If the blade is not aligned horizontally, align it properly by grinding off some metal from the
side bending downwards.
12.3 Cleaning the mower housing
Dirt deposits make the start difficult, affect the quality of the cut and the discharge of the grass.
Dirt and grass residues are easiest to remove immediately after the mowing. To avoid fouling
the floor, the underside must be cleaned on the grass.
Remove the mulching plug / grass catcher.
Fit the hose connector to the lawn mower and turn on the water tap.
Start the lawn mower and switch it off again after about 30 seconds. The rotating blade
bar will throw the water onto the underside of the lawn mower and thus clean it.
Turn off the water tap and remove the hose connector.
Clean the top with a cloth (do not use any sharp objects).
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo POWXG6026 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo POWXG6026 in the language / languages: English as an attachment in your email.

The manual is 0,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo POWXG6026

Varo POWXG6026 User Manual - German - 18 pages

Varo POWXG6026 User Manual - Dutch - 17 pages

Varo POWXG6026 User Manual - French - 17 pages

Varo POWXG6026 Additional guide - All languages - 3 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info