756782
6
Zoom out
Zoom in
Previous page
1/16
Next page
POWX07583 EN
Copyright © 2021 VARO P a g e | 6 www.varo.com
Before each use, check the saw blade for small cracks or damages. Replace a cracked or
damaged blade immediately.
Never use saw blades made of high-speed steel (HSS).
Only use saw blades that are recommended by the manufacturer and that fulfil the EN847-
1 standard. Also make sure the riving knife is not thicker than the width of the saw cut, and
that it is not thinner than the body of the saw blade.
Always use the accessories that are recommended by this manual.
Select the correct saw blade for the material must be sawn.
To reduce the generation of noise, always make sure that the blade is sharp and clean.
Only use correctly sharpened saw blades. Never exceed the maximum speed that is
indicated on the saw blade.
Before installing the saw blade, clean the axle, the flanges (especially the assembly
surfaces) and the hexagonal nut. Incorrect mounting can lead to vibrations/knocking or
slipping of the saw blade.
Wherever possible, use the upper saw blade guard and the riving knife with every type of
application, also when sawing material in two. Always mount the saw blade guard
according to the instructions in this manual. Cutting operations are those where the saw
blade cuts completely through the workpiece, such as for instance when doing longitudinal
cuts or shortening workpieces. NEVER use the equipment with a defective saw blade
guard, and never tie up a saw blade guard with a rope or cord. Every irregularity in the
operation of the saw guard must be immediately corrected.
Immediately replace the upper saw blade guard and the riving knife, after a process has
been completed that required their removal.
Prevent that the saw comes into contact with metals, such as nails and screws. Search for
and remove all nails, screws and other foreign materials from the workpiece, before you
start to work.
Remove spanners, cut off pieces and the other items from the saw table, before turning on
the switch.
NEVER wear gloves while working; the wearing of gloves is only recommended while
cutting tools are being replaced.
Make sure that your hands stay clear of the cutting line of the saw blade.
NEVER stand in the cutting line of the saw blade and NEVER let anyone else stand in that
position.
Make sure that the saw blade does not touch the riving knife or the workpiece, before you
turn on the switch.
Let the saw run for a few moments before inserting a workpiece. Listen for vibrations or
knocking of the saw blade, which can indicate improper mounting or balancing of the
blade.
The equipment may not be used for making grooves or recesses.
Replace the table insert when it is worn out.
NEVER make any adjustments on the machine while it is turning. Remove the plug from
the socket before making any adjustments.
If necessary, use a push block. A push block MUST be used for longitudinal sawing of
smaller workpieces, so that your hands and fingers are kept well away from the saw blade.
Always store your push block, whenever it is not in use.
Pay special attention to the instructions that help to reduce the hazard of KICK BACK.
KICK BACK is a sudden reaction to a jammed, bent or badly aligned saw blade. KICK
BACK causes the workpiece to be thrown back in the direction of the operator. KICK
BACK can lead to serious injuries. KICK BACK can be avoided by keeping your saw blade
sharp, by keeping the rip fence parallel to the saw blade, by maintaining the riving knife
and the upper saw blade guard in good condition and in the right position, by keeping a
good grip on the workpiece until you have pushed it completely past the saw blade, and by
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo POWX07583 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo POWX07583 in the language / languages: English as an attachment in your email.

The manual is 0,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo POWX07583

Varo POWX07583 User Manual - German - 17 pages

Varo POWX07583 User Manual - Dutch - 17 pages

Varo POWX07583 User Manual - French - 17 pages

Varo POWX07583 Additional guide - All languages - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info