756748
8
Zoom out
Zoom in
Previous page
1/12
Next page
POWDP25200 EN
Copyright © 2021 VARO P a g e | 8 www.varo.com
4. Store the charger and battery pack indoors, out of reach of children.
NOTE: If battery is hot after continuous use in the tool, allow it to cool down
to room temperature before charging. This will extend the life of your
batteries.
8.2 Removal / insertion of battery (Fig. 2)
WARNING: Before making any adjustments ensure the tool is switched off
or remove the battery pack.
Hold the tool with one hand and the battery pack (20) with the other.
To install: push and slide battery pack into battery port, make sure the release latch on the
rear side of the battery snaps into place and battery is secure before beginning operation.
To remove: Press the battery release latch and pull the battery pack out at the same time.
8.3 Battery capacity indicator (Fig. 3)
There are battery capacity indicators on the battery pack, you can check the capacity status of
the battery if you squeeze the button (22). Before using the machine, please press switch
trigger to check if the battery is full enough for properly working.
Those 3 LED might show the status of the capacity level of the battery:
3 LED’s are litt: Battery fully charged
2 LED’s are litt: Battery 60% charged
1 LED is litt: Battery almost discharged
9 ADJUSTMENTS
9.1 Replacing the saw blade (Fig. 4)
Only use sharp and undamaged saw blades. Cracked or bent saw blades must be replaced
immediately.
Place this circular saw on its side on a flat surface. Advice you bring the base plate (10)
down as if a minimum depth cut which is ease to operate.
Push the spindle lock button toward motor housing as the arrow shows in Fig. 4 and firmly
hold it.
Turn the blade clamp bolt clockwise by using the Allen key that supplied with the tool.
Remove the blade clamp bolt and outer flange.
Raise the lower guard (11) by using the lever for lower guard (9), and then remove the
saw blade.
Clean the saw blade flanges, then mount the new saw blade onto the output spindle and
against the inner flange.
Make sure the saw teeth and arrow on the blade is to be the same direction as the arrow
on the upper guard.
Reinstall the outer flange, and tighten the blade clamp bolt.
Make sure that the saw blade runs freely by turning the blade by hand.
9.2 Adjusting the depth of cut (Fig. 5)
The depth of cut is infinitely adjustable. A clean cut is achieved with the saw blade protruding
from the material by approx. 3 mm.
Loosen the lock lever for depth adjustment (16).
Hold the base plate (10) flat against the edge of the work piece and lift the body of the saw
until the blade is at the right depth determined by the depth gauge (17) (align the scale
line).
Tighten the lock lever for depth adjustment.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varo POWDP25200 CIRKELZAAG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varo POWDP25200 CIRKELZAAG in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varo POWDP25200 CIRKELZAAG

Varo POWDP25200 CIRKELZAAG User Manual - German - 13 pages

Varo POWDP25200 CIRKELZAAG User Manual - Dutch - 13 pages

Varo POWDP25200 CIRKELZAAG User Manual - French - 13 pages

Varo POWDP25200 CIRKELZAAG Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info