813304
6
Zoom out
Zoom in
Previous page
1/12
Next page
1. Flue or Chimney
1.1 The flue or chimney system must be in good condition.
It must be inspected by a competent person and passed for
use with the appliance before installation.
Products of combustion entering the room can cause
serious health risks.
1.2 The following must be checked:
The construction of the masonry chimneys, flue block
chimneys and connecting flue pipe system must meet
the requirements of the Building Regulations.
A flexible flue liner system can be used if certified for
use with solid fuel systems and installation complies with
manufacturersinstructionsandBuildingRegulations.
The flue liner must be replaced when an appliance is
replaced, unless proven to be recently installed and in
good condition.
If it is necessary to fit a register plate it must conform
to the Building Regulations.
The minimum height of the flue or chimney must
be 4.5m from the hearth to the top of the flue, with
no horizontal sections and a maximum of 4 bends.
Bends must have angles of less than 45 degrees from
the vertical.
Ensure the connecting flue pipe is kept a suitable
distance from any combustible material and does not
form part of the supporting structure of the building.
Make provision to remove the appliance without the
need to dismantle the chimney.
Installation Instructions
The flue/chimney system should not be supported by
the appliance.
Any existing flue must be confirmed as suitable for
the new intended use as defined in the Building
Regulations.
The flue or chimney systems must be inspected and
swept to confirm the system is structurally sound and
free from obstructions**.
If the chimney is believed to have previously
served an open fire it must be swept a second time
within a month of regular use after installation to clear
any soot falls that may have occurred due to
difference in combustion levels.
The flue exit from the building must comply with local
building control rules.
Do not connect or share the flue or chimney system
with another heating appliance.
1.3 Do not connect to systems containing large voids or spaces
over 230mm square.
1.4 Suitable access must be provided to enable the collection
and removal of debris.
1.5 The flue must be swept and inspected when the appliance is
installed.
Flue Draught
The flue draught must be checked with all windows and
doors closed and any extraction fans in this, or adjoining
rooms, running at maximum speed (see Installation
Checklist for ventilation requirements).
4.5
Flue Outlet Size
(Top or Rear Option)All
mm 128 153
inch 5 6
Flue/Chimney Size
May be reduced to 128mm (5") if burning approved
smokeless fuels or burning wood in an appliance
approved for use in a DEFRA smoke control area
Without flue liner Round (Diameter) mm 153 153
inch 66
Without flue liner system (Square) mm 135 135
inch 51/251/2
With Liner of Factory made system (diameter)
installed in accordance with manufacturers instructions
mm 153 153
inch 66
Flue/Chimney
minimum height**
All products
**must be 4.5m from the hearth to the top of the flue, with no horizontal sections
and a maximum of 4 bends. Bends must have angles of less than 45 degrees from
the vertical.
m 4.5 4.5
feet 15 15
Flue Draught
Min
mm Wg
1.0 1.0
Nominal 1.25 1.25
Max 2.0 2.0
European Min Spec for Chimney Flue - T400 N2 D 3 G50
NOTE: FLUE/CHIMNEY MUST NOT BE SMALLER THAN THE FLUE OUTLET SIZE
This table gives an overview of the flue and chimney options:
6
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varde Uniq at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varde Uniq in the language / languages: English as an attachment in your email.

The manual is 1.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Varde Uniq

Varde Uniq User Manual - English - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info