813325

Varde Bolton Manual

15
Zoom out
Zoom in
Previous page
1/24
Next page
15
How to light and stoke a fire
The first time you light up the stove, the enamel will temper and give off some smoke and a
slightly burnt smell. We recommend that you leave doors and windows open, as airing the room
will make the smell disappear.
This tempering softens the enamel, making it susceptible to damage. Therefore exercise caution
and avoid touching the enamel. We also recommend opening the door to the stove at regular
intervals during the first couple of hours to prevent the rope seal from sticking to the enamel.
Never use highly flammable liquids such as methylated spirit or petrol for lighting up!
We recommend using ‘top-down’ lighting, where you light the wood at the top of the combustion
chamber and not at the bottom. This is the most environmentally friendly method to light a fire.
The method will also help keep the glass clean. Place two small logs in a cross on the bottom
plate of the combustion chamber (approx. 1.3 kg) with a small distance between each log. Place
10 – 15 smaller sticks (approx. 1.2 kg) in a cross on top of the logs, and 1-2 firelighters at the
top and in between the sticks.
A thin layer of ash at the bottom of the stove makes it easier to light the fire.
Before lighting the stove, open the ignition air (See page 13 for how)
Once the fire burns, remember to close the ignition air vent and shaking grate again. Otherwise,
the stove and chimney might become overheated, which would invalidate the warranty.
A slight amount of soot may build up on side glass during the start-up fire. This is normal and
vanishes after a period.
Once the kindling has reduced to embers, we recommend opening the door slightly for a couple
of seconds to neutralise the negative pressure in the combustion chamber before opening the
door completely.
Place 2 logs in a cross on top of the embers (approx. 1.2 kg) and close the door again. To make
sure the wood ignites quickly, we recommend briefly opening the ignition air vent and make
sure you remember to close it again once the fire gets going. You can then adjust the combus-
tion air according to your heating requirements.
Take care not to shut off the air supply completely, otherwise the fire will die. The fire should
always burn bright and clear.
In most instances, however, you will have to identify the best combustion air settings your-
self, as the height and draught of your chimney as well as the quality of the firewood are deci-
sive factors in determining the best settings for your particular stove.
If the nominal heat output of your stove is too high compared to your heating requirements, you
can reduce the output as follows:
- Stoke a smaller amount of wood than usual, for example 1 kg, preferably consisting of 3 – 4
smaller pieces of wood. Apply full air to ignite the wood properly before reducing the combustion
air, perhaps down to approx. 60%. Be careful not to reduce the air supply to the point that the
fire dies. The fire should always burn bright and clear.
With this method it is possible, depending on the chimney, wood quality, etc., to reduce the
stove’s heat output from a nominal 7 kW down to perhaps 3 kW.
Please be aware that it can lead to poor combustion if you reduce the combustion air too much,
resulting in a lower efficiency and increased emission levels (increased pollution).
When refilling the stove with wood, we recommend opening the stove door once only embers
are left in the combustion chamber. Opening the door while flames are still burning and produc-
ing smoke and gas might cause smoke to escape into the room.
If you have problems lighting or operating the stove, see the section on Troubleshooting.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varde Bolton at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varde Bolton in the language / languages: English as an attachment in your email.

The manual is 1.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info