813332

Varde Anholt Manual

15
Zoom out
Zoom in
Previous page
1/24
Next page
15
How to light and stoke a fire:
The first time you light up the stove the enamel will temper, and give off some smoke and a
slight smell. We recommend that you leave doors and windows open, as airing the room will
make the smell disappear. This tempering softens the enamel making it susceptible to damage.
Therefore exeercise caution and avoid touching the enamel. Likewise we recommend opening
the door to the stove at regular intervals for the first hours to prevent the insulations rope from
sticking to the enamel.
Never use highly inflammable fluids such as methylated sprit and petrol for lighting up!
We recommend a ”Top-Down” lightning, where you light the wood in the upper area of the com-
bustions chamber and not in the ground. This method is the most environmental metod to light
a fire. The metod will keep the glass clean. In the combustion chamber you make a cross (╬) of
4 small pieces of wood with a small distance between each one of them(0,7-1,1kg). On top you
of them you make another cross (╬) of 8-12 smaller sticks (0,4-0,7 kg.), on top of this firewood
and in between use 2-3 kildning blocks. In total approximate 1,5kg og woods. A thin layer of
ashes at the bottom of the stove makes lighting up a fire easier.
Before lighting up the stove, open ignition air on the ash-pan for access of primary air .The
throttle for the Combustion Air is drawn towards the right and hereby fully openes for combusti-
on air.
When the fire burns remember to close the the Ignition air again, or the stove and chimney
might become overheated and will invalidate the warranty. Also make sure the ash pan is closed
propper.
Hereafter the combustion air are ajusted to the need of heat. Be aware not to close to much for
the air supply, otherwise the fire will die, the fire must alway be bright and clear.
In most instances, however, you will have to achieve the best combustion air settings your-
self, as the height and draught of your chimney, as well as the quality of the firewood are deci-
sive factors in determining how your particular stove is best set.
If the stove nominal heat output is too large compared to the heat demand, you can reduce the
output as descriped here:
- use a smaller amount of wood than usual, for example. 0,9 to 1.2 kg. and preferably consist-
end of 3-4 smaller pieces of wood. Apply full air to ignite the wood properly, then you can
reduce the combustion air, perhaps down to approx. 60%. Be aware not to close to much for the
air supply, otherwise the fire will die, the fire must alway be bright and clear.
With this method it, (depending on the chimney, wood quality, etc. is possible to reduce the
stove heat output from a nominal 5,5 kW down to maybe 3 to 3.5 kW.
Please be aware that it can lead to poor combustion, if you regulate too much down the com-
bustion air, resulting in a lower efficiency and increased emission levels in the smoke.
(increasing pollution).
Tertiary air
If you are wondering why your stove is fitted with an gap in the rear vermiculite plate in the
combustion chamber, with small holes through the back steel plate, where air is running through
into the combustion chamber. This is merely a consequence of our newly developed combustion
system. We refer to these air ducts as the ‘tertiary air’, and will prove helpful as you install your
new Varde stove.
When refilling the stove with wood, we recommend opening the stove door only once embers
are left in the combustion chamber. Opening the door whilst the flames are still burning and
producing smoke and gas, might cause smoke to slip into the room instead of up the chimney.
Should you have some issuses with the lightning or the function, see section on troubleshoo-
ting.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Varde Anholt at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Varde Anholt in the language / languages: English as an attachment in your email.

The manual is 1.33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info