611085

Valor 722AN Manual

11
Zoom out
Zoom in
Previous page
1/20
Next page
11
10. GAS SUPPLY CONNECTION
10.1 Fit the gas valve and connector unit to the supply
line.
10.2 Refit the burner unit to the convection box with
three screws.
10.3 Connect the elbow on the gas valve unit to the
burner unit.
10.4 Pressure testing supply line.
Make sure that the gas valve is shut off (control
knob bar at 90° to supply pipe line of flow).
The appliance and its appliance main gas valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at test
pressures in excess of 1/2 psig (3.5kPa). The
appliance must be isolated from the gas supply
piping system by closing the equipment shut off
valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than
1/2 psig (3.5kPa).
11. CERAMIC WALLS
INSTALLATION
11.1 Fit the ceramic rear wall inside the “L” brackets
on the back face of the burner compartment. Push
the ceramic wall flat against the back face of the
burner compartment (See figure 15).
11.2 The ceramic side walls can be installed in two
alternative arrangements:
a) With the brick pattern visible - Fit the wall
stamped “A” at the right side and the wall
stamped “B” at the left side.
b) With the plain wall surfaces visible - Fit the
wall stamped “B” at the right side and the wall
stamped “A” at the left side.
Find out which arrangement the customer requires.
Explain that the customer can not alter the wall
arrangement after the front casting is installed.
Fit the ceramic side walls against the side faces of
the burner compartment. The bottom edges of
the walls should rest on the ledges at the sides of
the fire box and the top of the walls should locate
in the space between the black cross member and
the side walls of the burner compartment (See
figure 16).
12. FRONT & CONTROL
LINKAGE INSTALLATION
12.1 Remove the tape securing the control linking bar to
the casting/surround. Slide the control knob
upwards as far as it will go. This will make sure that
the bottom of the linking bar is higher than the
bottom of the casting/surround when fitting it to
the fireplace
.
12.2 “Adorn front”; Carefully lift the casting. Do not lift
it by the control knob. Place it against the fireplace
front surface so that the retaining strip at the back of
the casting is above the two upper retaining
brackets at the top of the convection box. Lower the
casting making sure that the rear retaining strip
locates fully over the retaining brackets on the
convection box (See figure 17).
Fig. 15 Ceramic rear wall installation
Fig. 16 Ceramic side walls installation
Fig. 17 “Adorn” front casting top location
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Valor 722AN at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Valor 722AN in the language / languages: English as an attachment in your email.

The manual is 0,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info