602563

Vaillant VRC 430f Manual

38
Zoom out
Zoom in
Previous page
1/40
Next page
Installation instructions VRC 430f 0020042470_0118
Heating curve
A heating curve shows the relationship between the out-
side temperature and the flow temperature. The selec-
tion of a heating curve allows the influencing of the flow
temperature of your heating system and therefore also
the room temperature.
The option of being able to choose from a range of
heating curves facilitates optimum adaptation of the
control to the apartment and the heating system in con-
junction with the switch-on room temp. (see menu).
Fig. G.1 shows the possible heating curves for a room
target temperature of 20 °C.
If, for example, heating curve 1.5 is selected, a flow tem-
perature of 56 °C is maintained with an outside
temperature of 0 °C.
Fig. G.1 Diagram with heating curves for a target room temper-
ature of 20 °C
Axis a
20
2
2
18
Feed temperature
in ºC
Outside temperature in ºC
Fig. G.2 Parallel heating curve offsetting
If heating curve 1.5 is selected and 22 °C rather than
20 °C is specified as the room target temperature , the
heating curve is displaced as shown in Fig. G.2. The
heating curve is displaced according to the value of the
room target temperature along axis a which is angled at
45°, i.e. the controller ensures a flow temperature of
67 °C with an outside temperature of 0 °C.
Heating flow temperature
Your appliance heats water which is pumped through
your heating system. The temperature of this hot water
as it leaves the appliance is referred to as the flow tem-
perature.
Interior temperature
The interior temperature, also referred to as room tem-
perature, is the actual current temperature in your
apartment.
Maximum temperature, solar cylinder
In order to ensure the highest possible returns from the
solar cylinder heating, while at the same time ensuring
that scalding/limescale protection is active, you can set
a maximum value for the solar temperature cylinder.
To do this, use the "Cylinder temp. top" SP1 sensor for
cylinder 1, if this is installed in the corresponding cylin-
der. Otherwise "Cylinder temp. bottom" SP2 is used.
SP3 is used for the second cylinder, swimming pool).
If the set temperature is exceeded, the solar circuit
pump is switched off. Solar power is only permitted
once the temperature on the active sensor drops 1.5 K
below the maximum temperature.
The maximum temperature for each cylinder can set
separately.
– Cylinder_Maximumtemperature_1:
20 ... 85 °C; Basic value 70 °C
– Cylinder_Maximumtemperature_2:
20 ... 85 °C; Basic value 60 °C
The programmed maximum temperature must not ex-
ceed the cylinder's maximum permisible water tempera-
ture!
Parameter
Parameters are the properties of your heating system.
You can influence these properties by altering the value
of a parameter, e.g. by reducing the value of the param-
eter "set-back temp" from 15 °C to 12 °C.
Switch-on room temp. (operating level for expert
technicians)
You can specify whether or not the temperature sensor
fitted in the VRC 430f should be used in screen C8 "HC1
Parameter" under the "Switch-on room temp." menu
item.
The following inputs are possible in the menu point
"Switch-on room temp.":
– None
The temperature sensor is not used for control.
– Switch on
The in-built temperature sensor measures the current
room temperature in the reference room. This value is
compared with the target room temperature and the
Appendix
Glossary
… 38


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vaillant VRC 430f at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vaillant VRC 430f in the language / languages: English as an attachment in your email.

The manual is 6,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info