469481
19
Zoom out
Zoom in
Previous page
1/64
Next page
17Bedienungsanleitung atmoTEC pro/atmoTEC plus und turboTEC pro/turboTEC plus 0020029202_01
4.7.2 Störungen beim Zündvorgang
bar
2
1
Abb. 4.15 Entstörung
(hier abgebildet: atmoTEC/turboTEC plus)
Wenn der Brenner nach drei Zündversuchen nicht gezün-
det hat, geht das Gerät nicht in Betrieb und schaltet auf
Störung. Dies wird durch die Anzeige der Fehlercodes
F. 2 8 ” oder „F. 29 ” im Display angezeigt.
atmoTEC/turboTEC plus:
Zusätzlich erscheint im Display das durchkreuzte Flam-
mensymbol (1).
atmoTEC/turboTEC pro:
Zusätzlich leuchtet die rote Anzeigeleuchte.
Eine erneute automatische Zündung erfolgt erst nach
einer manuellen Entstörung.
Drücken Sie zur Entstörung den Entstörknopf (2) und
halten Sie ihn ca. eine Sekunde lang gedrückt.
a
Achtung!
Beschädigungsgefahr durch unsachgemäße
Veränderungen!
Wenn Ihr Gas-Wandheizgerät nach dem dritten
Ent stör versuch immer noch nicht in Betrieb
geht, müssen Sie einen anerkannten Fachhand-
werks betrieb zwecks Überprüfung zu Rate
ziehen.
4.7.3 Störungen im Abgasweg
Alle atmoTEC/turboTEC-Geräte sind mit einer Überwa-
chungseinrichtung des Abgasweges ausgestattet. Bei
nicht ordnungsgemäßer Funktion des Abgasweges schal-
tet das Gerät ab.
- Im Display der Geräte atmoTEC/turboTEC plus erschei-
nen dann die Symbole
und .
- Bei den atmoTEC/turboTEC pro-Geräten leuchtet die
rote LED dauerhaft.
- Bei allen Geräten erscheint eine Fehlermeldung:
atmoTEC: F. 3 6
turboTEC: F. 3 3
a
Achtung!
Beschädigungsgefahr durch unsachgemäße
Veränderungen!
Bei dieser Fehlermeldung müssen Sie einen
anerkannten Fachhandwerks betrieb zwecks
Überprüfung zu Rate ziehen.
4.7.4 Gerät/Heizungsanlage füllen
bar
2
1
Abb. 4.16 Fülldruck der Heizungsanlage kontrollieren
(hier abgebildet: atmoTEC/turboTEC plus)
Kontrollieren Sie vor der Inbetriebnahme den Fülldruck
der Anlage im Display (1) oder am Manometer (2). Für
einen einwandfreien Betrieb der Heizungsanlage soll
bei kalter Anlage im Display ein Fülldruck zwischen 1,0
und 2,0 bar angezeigt werden (am Manometer befindet
sich der Zeiger dann im hellgrauen Bereich). Beträgt
der Fülldruck weniger als 0,8 bar (der Zeiger des Ma-
nometers ist dann im dunkelgrauen Bereich), muss vor
der Inbetrieb nahme Wasser nachgefüllt werden.
h
Hinweis!
Die Anzeige des Anlagendrucks im Display
funktioniert nur, wenn das Gerät an das Strom-
netz angeschlossen und eingeschaltet ist!
Hinweis!
(nur für atmoTEC/turboTEC mit angeschlosse-
nem Warmwasserspeicher)!
Im Lieferumfang des Gerätes ist eine
Fülleinrichtung enthalten. Sie wird von Ihrem
Fachhandwerksbetrieb bauseits installiert.
Erstreckt sich die Heizungsanlage über mehrere Stock-
werke, so kann ein höherer Fülldruck der Anlage erfor-
derlich sein. Fragen Sie hierzu Ihren Fachhandwerks-
betrieb.
Bedienung 4
BEDE
19


Need help? Post your question in this forum.

Forumrules
1

Forum

vaillant-turbotec-pro

Reset search

  • Hi - I have just arrived back to Spain after 7 months - and when I turned on the GAS I couldn't get any warm water - the GAS in the kitchen was OK. After few seceonds it shows F75 and no warm water.
    What to do? I have a turbo TEC Pro. Submitted on 11-4-2022 at 17:46

    Reply Report abuse
  • Good morning
    Boiler vaillant turbotec
    When i turn on the boiler the pressure is rising to the maximum ( end of red) over 3.5 bar
    How can i fix this problem?
    Thank you Submitted on 18-10-2020 at 11:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vaillant turboTEC pro at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vaillant turboTEC pro in the language / languages: German, Dutch, French as an attachment in your email.

The manual is 6,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vaillant turboTEC pro

Vaillant turboTEC pro Manual - Dutch - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info