Manual Vaillant ecoVIT exclusiv VKK 366-4 (page 14 of 16) (English)

748582

Zoom out

Zoom in

1/16

Operating instructions

ecoVIT exclusiv

VKK 226/4 – VKK 656/4

AT, DE

Publisher/manufacturer

Vaillant GmbH

Berghauser Str. 40 D-42859 Remscheid

Tel. +49 21 91 18‑0 Fax +49 21 91 18‑2810

info@vaillant.de www.vaillant.de

Contents

2 Operating instructions ecoVIT exclusiv 0020258609_00

Contents

1 Safety .................................................................... 3

1.1 Action-related warnings ......................................... 3

1.2 Intended use.......................................................... 3

1.3 General safety information .................................... 3

2 Notes on the documentation .............................. 5

2.1 Observing other applicable documents ................. 5

2.2 Storing documents................................................. 5

2.3 Validity of the instructions ...................................... 5

3 Product description............................................. 5

3.1 Design of the product............................................. 5

3.2 Opening the front flap ............................................ 5

3.3 Control elements.................................................... 5

3.4 Frost protection function ........................................ 7

3.5 Type designation and serial number ..................... 7

3.6 CE label ................................................................. 7

4 Operation.............................................................. 7

4.1 Adjustment and display levels ............................... 7

4.2 Starting up the product .......................................... 7

4.3 Setting the language.............................................. 8

4.4 Setting the heating flow temperature .................... 8

4.5 Setting the cylinder temperature............................ 9

4.6 Switching off the functions..................................... 9

4.7 Status code meanings ......................................... 10

5 Care and maintenance ...................................... 10

5.1 Caring for the product .......................................... 10

5.2 Maintenance ........................................................ 10

5.3 Guaranteeing the correct filling pressure of the

heating installation............................................... 10

5.4 Checking the condensate discharge pipe and

tundish ................................................................. 11

5.5 Carrying out the flue gas analysis ....................... 11

6 Troubleshooting ................................................ 12

6.1 Eliminating faults.................................................. 12

6.2 Checking the product status ................................ 12

7 Decommissioning.............................................. 12

7.1 Temporarily decommissioning the product.......... 12

7.2 Permanently decommissioning the product......... 13

8 Recycling and disposal..................................... 13

9 Guarantee and customer service..................... 13

9.1 Guarantee............................................................ 13

9.2 Customer service................................................. 13

Appendix ............................................................................ 14

A Status codes ...................................................... 14

B Troubleshooting ................................................ 14

Safety 1

0020258609_00 ecoVIT exclusiv Operating instructions 3

1 Safety

1.1 Action-related warnings

Classification of action-related warnings

The action-related warnings are classified in

accordance with the severity of the possible

danger using the following warning signs and

signal words:

Warning symbols and signal words

Danger!

Imminent danger to life or risk of

severe personal injury

Danger!

Risk of death from electric shock

Warning.

Risk of minor personal injury

Caution.

Risk of material or environmental

damage

1.2 Intended use

There is a risk of injury or death to the user or

others, or of damage to the product and other

property in the event of improper use or use

for which it is not intended.

The products are gas-fired floor-standing

condensing boilers and are intended for use

in this function as heat generators for closed

domestic hot water central heating installa-

tions and for central domestic hot water gen-

eration.

Intended use includes the following:

– observance of the operating instructions

included for the product and any other

installation components

– compliance with all inspection and main-

tenance conditions listed in the instruc-

tions.

This product can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabil-

ities or lack of experience and knowledge if

they have been given supervision or instruc-

tion concerning use of the product in a safe

way and understand the hazards involved.

Children must not play with the product.

Cleaning and user maintenance work must

not be carried out by children unless they are

supervised.

Any other use that is not specified in these

instructions, or use beyond that specified in

this document shall be considered improper

use. Any direct commercial or industrial use

is also deemed to be improper.

Caution.

Improper use of any kind is prohibited.

1.3 General safety information

1.3.1 Installation by skilled tradesmen

only

The installation, inspection, maintenance

and repair of the product, as well as the gas

ratio settings, must only be carried out by a

competent person.

1.3.2 Danger caused by improper

operation

Improper operation may present a danger to

you and others, and cause material damage.

▶ Carefully read the enclosed instructions

and all other applicable documents, par-

ticularly the "Safety" section and the warn-

ings.

▶ Only carry out the activities for which in-

structions are provided in these operating

instructions.

1.3.3 Risk of death from escaping gas

What to do if you smell gas in the building:

▶ Avoid rooms that smell of gas.

▶ If possible, open doors and windows fully

and ensure adequate ventilation.

▶ Do not use naked flames (e.g. lighters,

matches).

▶ Do not smoke.

▶ Do not use any electrical switches, mains

plugs, doorbells, telephones or other com-

munication systems in the building.

▶ Close the emergency control valve or the

main isolator.

▶ If possible, close the gas isolator cock on

the product.

▶ Warn other occupants in the building by

yelling or banging on doors or walls.

▶ Leave the building immediately and ensure

that others do not enter the building.

1 Safety

4 Operating instructions ecoVIT exclusiv 0020258609_00

▶ Alert the police and fire brigade as soon as

you are outside the building.

▶ Use a telephone outside the building to

inform the emergency service department

of the gas supply company.

1.3.4 Risk of death due to a blocked or

leaking flue gas pipe

What to do if you smell flue gas in the prop-

erty:

▶ Open all accessible doors and windows

fully to provide ventilation.

▶ Switch off the product.

▶ Inform a competent person.

1.3.5 Risk of death due to explosive and

flammable materials

▶ Do not use the product in storage rooms

that contain explosive or flammable sub-

stances (such as petrol, paper or paint).

1.3.6 Risk of death due to changes to the

product or the product environment

▶ Never remove, bridge or block the safety

devices.

▶ Do not tamper with any of the safety

devices.

▶ Do not damage or remove any seals on

components.

▶ Do not make any changes:

– The product itself

– to the gas, air, water and electricity sup-

plies

– to the entire flue gas installation

– to the entire condensate drain system

– to the expansion relief valve

– to the drain pipework

– to constructional conditions that may

affect the operational reliability of the

product

1.3.7 Risk of poisoning caused by

insufficient supply of combustion

air

Conditions: Open-flued operation

▶ Ensure that there is a sufficient supply of

combustion air.

1.3.8 Risk of corrosion damage due to

unsuitable combustion and room air

Sprays, solvents, chlorinated cleaning

agents, paint, adhesives, ammonia com-

pounds, dust or similar substances may lead

to corrosion on the product and in the air/flue

pipe.

▶ Ensure that the supply of combustion air is

always free of fluorine, chlorine, sulphur,

dust, etc.

▶ Ensure that no chemical substances are

stored at the installation site.

1.3.9 Risk of material damage caused by

frost

▶ Ensure that the heating installation always

remains in operation during freezing con-

ditions and that all rooms are sufficiently

heated.

▶ If you cannot ensure the operation, have a

competent person drain the heating install-

ation.

1.3.10 Risk of injury and material damage

due to maintenance and repairs

carried out incorrectly or not

carried out at all

▶ Never attempt to carry out maintenance

work or repairs on your product yourself.

▶ Faults and damage should be immediately

rectified by a competent person.

▶ Adhere to the maintenance intervals spe-

cified.

1.3.11 Risk of structural damage caused

by escaping water

Escaping water can cause damage to the

building.

▶ If there is a possibility of leaks in the pipe-

work, close the service valves immedi-

ately.

▶ Have any leaks eliminated by your heating

specialist company.

Notes on the documentation 2

0020258609_00 ecoVIT exclusiv Operating instructions 5

2 Notes on the documentation

2.1 Observing other applicable documents

▶ You must observe all operating instructions enclosed with

the system components.

2.2 Storing documents

▶ Keep this manual and all other applicable documents

safe for future use.

2.3 Validity of the instructions

These instructions apply only to:

Product article number

VKK 226/4-H

0010007508

VKK 226/4-L

0010007688

VKK 286/4-H

0010007512

VKK 286/4-L

0010007692

VKK 366/4-H

0010007516

VKK 366/4-L

0010007696

VKK 476/4-H

0010007520

VKK 476/4-L

0010007700

VKK 656/4-H

0010007524

VKK 656/4-L

0010007704

3 Product description

3.1 Design of the product

1 Panel

2 Control elements

3 Front flap

3.2 Opening the front flap

▶ Take hold of the recessed handle in the front flap and lift

the panel up slightly.

◁ The front flap automatically swivels downwards and

the control panel becomes accessible.

3.3 Control elements

1 Display 2 i button

3 Product description

6 Operating instructions ecoVIT exclusiv 0020258609_00

3 Control (accessory)

4 Main switch

5 + button

6 − button

7 Reset button

8 Heating flow temperat-

ure rotary knob

9 Cylinder temperature

rotary knob

The display shows the current heating flow temperature, the

filling pressure of the heating installation, the operating mode

or certain additional information.

The i button is used to call up status information.

The control, which is available as an accessory, automatic-

ally controls the flow temperature depending on the outdoor

temperature.

The main switch is used to switch the product on and off.

The + button is used to display the cylinder temperature (if

the product is equipped with a cylinder temperature sensor).

The − button is used to display the filling pressure of the

heating installation.

The Reset button is used to reset the product in the case of

certain faults.

The heating flow temperature rotary knob is used to set the

heating flow temperature if no control is connected. If a con-

trol is connected, the heating flow temperature rotary knob

should be turned clockwise as far as it will go.

The cylinder temperature rotary knob is used to set the cyl-

inder temperature if a domestic hot water cylinder is connec-

ted.

If a control is connected, the rotary knob should be turned

clockwise as far as it will go. The control then determines the

cylinder temperature.

3.3.1 Digital Information and Analysis System

(DIA)

1 Display showing the

current heating flow

temperature, the filling

pressure in the heating

installation, or a status

or fault code

2 Plain text display

3.3.2 Displayed symbols

Symbol Meaning Explanation

Fault in the air/flue gas

route

Fault in the air/flue gas

route

Symbol Meaning Explanation

comDIALOG The heating flow and do-

mestic hot water temper-

ature are specified via

the comDIALOG com-

munications system. The

product works at temper-

atures other than those

set at the rotary knob.

This operating mode can

only be terminated by:

– comDIALOG

– Changing the tem-

perature at the rotary

knobs by more than

± 5 K

This operating mode

cannot be terminated by:

– Pressing the Reset

button.

– Switching the

product off and on

again

Heating mode – Symbol perman-

ently on: Product is

in heating mode op-

erating mode

– Symbol flashing:

Burner anti-cycling

time is active

Hot water generation – Symbol permanently

visible: Charging

mode for the do-

mestic hot water

cylinder is enabled

by the control and

floor-standing boiler

control system

– Symbol flashes:

Domestic hot water

cylinder is being

heated

Heating pump operating

Solenoid valve is actu-

ated

Gas supply to the burner

is open

Current energy demand Display of the current

burner modulation rate

(bar graph display)

Fault during burner

operation

Burner is switched off

Burner operating cor-

rectly

Burner is switched on

Operation 4

0020258609_00 ecoVIT exclusiv Operating instructions 7

3.4 Frost protection function

The product is equipped with a frost protection function.

If the heating flow temperature falls below 5 °C when the

main switch is on, the product starts up and heats the cir-

culating water to approx. 30 °C.

Caution.

Risk of material damage due to frost.

The frost protection function cannot guaran-

tee flow through the entire heating installa-

tion, which means that parts of the heating

installation may freeze and therefore become

damaged.

▶ During a period of frost, ensure that the

heating installation remains in operation

and that all rooms are sufficiently heated,

even when you are away.

▶ Consult a competent person about this.

3.5 Type designation and serial number

The type designation and the serial number are located on a

sticker below the control panel behind the front flap.

The data plate can only be seen by the competent person.

▶ Open the front flap. (→ Page 5)

▶ Read off the type designation and the serial number from

the sticker.

3.6 CE label

The CE label shows that the products comply with the basic

requirements of the applicable directives as stated on the

identification plate.

The declaration of conformity can be viewed at the manufac-

turer's site.

4 Operation

4.1 Adjustment and display levels

The product has two adjustment and display levels.

The end user level contains information and setting options

that you require as the end user.

The installer level is reserved for the competent person. It is

protected by a code. Only competent persons may change

any settings in the installer level.

4.2 Starting up the product

4.2.1 Opening the isolator devices

1. Ask the competent person who installed the product to

explain to you where these isolator devices are located

and how to handle them.

2. Open the gas stopcock fully.

3. Check that the heating installation flow and return

service valves are open, if such service valves are

installed.

4. If a domestic hot water cylinder is connected, open the

cold-water isolation valve. To check, you can turn on a

hot water tap and see whether water is escaping there.

4.2.2 Switching on the product

1 Main switch 2 Display

1. Use the main switch (1) to switch on the product.

◁ 1: "ON"

◁ When the main switch is in position 1, the product is

switched on and the standard display for the Digital

Information and Analysis System is shown in the

display. The function menu is immediately shown

in the display once the product has been switched

on. The function menu enables competent persons

to control how the individual actuators work. The

product returns to normal operating mode after a

waiting period of approximately five seconds or if the

− button is pressed.

2. Set up your product according to your needs.

4 Operation

8 Operating instructions ecoVIT exclusiv 0020258609_00

4.2.3 Switching off the product

1 Main switch 2 Display

▶ Use the main switch (1) to switch off the product.

◁ 0: "OFF"

Note

In order for the protection modes, such as

frost protection, to remain activated, only ac-

tivate and deactivate the product using the

control (you can find information about this in

the relevant operating instructions). If no con-

trol is present, block the heating and cylinder

charging mode by turning the dial to the anti-

clockwise end stop.

4.3 Setting the language

▶ Contact your competent person so that they can set the

correct language for the control panel.

4.4 Setting the heating flow temperature

Conditions: Control connected

1 Main switch 2 Heating flow temperat-

ure rotary knob

▶ Turn the rotary knob for the heating flow temperature (2)

as far as it will go clockwise.

◁ The heating flow temperature is automatically set by

the control.

Note

To ensure that the control can set temper-

atures up to the maximum heating flow

temperature, the rotary knob for the heating

flow temperature should always be set to the

clockwise end stop.

Conditions: No control connected

1 Heating flow temperat-

ure rotary knob

2 Displaying the current

heating flow temperat-

ure

▶ Set the target flow temperature on the rotary knob for

the heating flow temperature (1) in accordance with the

outdoor temperature.

Position Meaning

Outdoor temperat-

ure

Fully left Frost protection

Anti-clockwise (but

not at the end stop)

Transition Time

Approx.

10 … 20 ℃

Centre Moderate cold

Approx.

0 … 10 ℃

Clockwise Extreme cold

Below

0 ℃

◁ After turning the rotary knob for the heating flow tem-

perature, the display shows the set target flow tem-

perature (2). After three seconds, this display goes

out and the default display reappears (current heat-

ing flow temperature).

Note

The maximum heating flow temperature is set

in the factory at 75 °C. This can be defined by

the competent person to be between 40 °C

and 85 °C.

Operation 4

0020258609_00 ecoVIT exclusiv Operating instructions 9

4.5 Setting the cylinder temperature

Conditions: Control connected

1 Display 2 Cylinder temperature

rotary knob

▶ Set the rotary knob for the cylinder temperature (2) as

far as it will go clockwise so that the control can work

without any faults occurring.

▶ Do not set the required cylinder temperature on the

rotary knob for the cylinder temperature; set the cylinder

temperature on the control instead.

Conditions: No control connected

1 Display 2 Cylinder temperature

rotary knob

▶ Set the rotary knob for the cylinder temperature (2) to

the required cylinder temperature.

Position of the rotary knob for setting the cylinder tem-

perature (→ Page 9)

◁ The required temperature is shown in the display

(1). After three seconds, this display goes out and

the default display reappears (current heating flow

temperature).

Note

The maximum cylinder temperature is set in

the factory at 65 °C. This can be defined by

the competent person to be between 50 °C

and 70 °C.

Note

If a cylinder temperature lower than 60 °C is

required, we recommend that you regularly

use the anti-legionella function via the control.

Position Meaning Temperature

Fully left Minimum cylinder

temperature = frost

protection

15 ℃

Centre Medium cylinder

temperature

≈ 50 ℃

Fully right Maximum cylinder

temperature

65 ℃

4.6 Switching off the functions

4.6.1 Switching off heating mode

Note

You can completely switch off heating mode in

summer without switching off the hot water gener-

ation.

1 Rotary knob for setting

the heating flow temper-

ature

▶ To switch off heating mode, turn the rotary knob for set-

ting the heating flow temperature (1) as far as it will go

anti-clockwise. If the product is controlled by a control,

use this control to switch off heating mode and leave the

rotary knob at the clockwise end stop.

Note

The product's internal frost protection is there-

fore guaranteed whether there is a control or

not.

4.6.2 Switching off cylinder charging mode

(using the VRC 630/VRS 620 control)

1. Leave the rotary knob for the cylinder temperature at

the clockwise end stop.

2. Switch the cylinder circuit to "OFF" on the control.

Note

If the VRC 450 or VRC 700 control is avail-

able, switch cylinder charging mode off in

accordance with the section "Switching off

cylinder charging mode (without a control)

(→ Page 10)".

5 Care and maintenance

10 Operating instructions ecoVIT exclusiv 0020258609_00

4.6.3 Switching off cylinder charging mode

(without control)

▶ Turn the rotary knob for the cylinder temperature to the

anti-clockwise end stop.

◁ Cylinder charging mode is switched off.

◁ The frost protection function is activated for the do-

mestic hot water cylinder.

◁ The display shows the target cylinder temperature of

15 °C for three seconds.

– 15 ℃

Note

The effect of the frost protection function is

that, at cylinder temperatures below 10 °C, the

domestic hot water generation is switched on

until the water in the cylinder has reached 15

°C again.

4.7 Status code meanings

The status codes that are shown in the DIA system's display

provide information about the product's current operating

status.

If several operating statuses occur at the same time, the

applicable status codes are displayed alternately, one after

the other. The status code is explained a plain text display in

the display.

Status codes (→ Page 14)

5 Care and maintenance

5.1 Caring for the product

Caution.

Risk of material damage caused by un-

suitable cleaning agents.

▶ Do not use sprays, scouring agents, de-

tergents, solvents or cleaning agents that

contain chlorine.

▶ Clean the casing with a damp cloth and a little solvent-

free soap.

5.2 Maintenance

An annual inspection and biennial maintenance of the

product carried out by a competent person is a prerequisite

for ensuring that the product is permanently ready and safe

for operation, reliable, and has a long working life. The

inspection may require maintenance to be carried out earlier,

depending on the results.

5.3 Guaranteeing the correct filling pressure of

the heating installation

5.3.1 Checking the system pressure

1 − button

▶ Check the heating installation's filling pressure at regular

intervals. Briefly press the − button.

◁ The display will show the filling pressure for approx-

imately 5 seconds.

◁ The filling pressure must be between 0.1 MPa and

0.2 MPa (1.0 and 2.0 bar) when the heating installa-

tion is cold in order for the heating installation to op-

erate properly. If the pressure is lower, you must add

heating water before starting up.

Note

You can permanently switch between the tem-

perature or pressure display in the display by

pressing and holding the – button for approx-

imately five seconds.

Note

To avoid operating the heating installation with

an insufficient water volume and to prevent

potential subsequent damage, the product

is fitted with a pressure sensor. The pres-

sure sensor signals the low pressure level if

the level falls below 0.06 MPa (0.6 bar). This

is signalled by the system pressure value in

the display flashing. If the level falls below

0.03 MPa (0.3 bar), the system displays the

fault message and F.22 alternately, and the

burner is blocked. If the system pressure is

lower than 0.06 MPa (0.6 bar), fill the heat-

ing installation up again as quickly as pos-

sible. As soon as the system pressure ex-

ceeds 0.06 MPa (0.6 bar), the product starts

up without any further measures being re-

quired.

If the pressure sensor is defective, the

product enters comfort protection mode. The

maximum possible flow temperature and the

power are limited. The status S.40 and F.22

(water deficiency) are displayed alternately.

Note

If the heating installation extends over several

floors, a higher system pressure for the heat-

ing installation may be necessary. Ask your

competent person for details.

Care and maintenance 5

0020258609_00 ecoVIT exclusiv Operating instructions 11

5.3.2 Filling the heating installation

Caution.

Risk of material damage due to heating

water that is extremely calciferous or cor-

rosive or contaminated by chemicals.

Unsuitable tap water damages the seals

and diaphragms, blocks components in the

product and heating installation through

which the water flows and causes noise.

▶ Only fill the heating installation with suit-

able heating water.

▶ In case of doubt, ask a competent person

for details.

1. Ask a competent person where the filling cock is loc-

ated.

2. Connect the filling cock to a hot water supply in the way

you were told by the competent person.

3. Open all radiator valves (thermostatic radiator valves) of

the heating installation.

4. Open the hot water supply.

5. Slowly open the filling cock.

6. Fill it with water until the required filling pressure is

reached.

7. Close the hot water supply.

8. Purge all radiators.

9. Then check the filling pressure on the display.

10. Top up with more water if necessary.

11. Close the filling cock.

5.4 Checking the condensate discharge pipe

and tundish

The condensate discharge pipe and tundish must always be

penetrable.

▶ Regularly check the condensate discharge pipe and tun-

dish for faults and, particularly, for blockages.

You must not be able to see or feel any obstructions in the

condensate discharge pipe and tundish.

▶ If you notice a fault, have it eliminated by a competent

person.

5.5 Carrying out the flue gas analysis

Note

Measurement and inspection work must only be

carried out by the chimney sweep or competent

person.

1 + button 2 − button

1. Switch on the chimney sweep function by pressing the

− and + buttons for the DIA system at the same time.

◁ Shown in the display: S.Fh = Heating chimney

sweep mode; S.Fb = Domestic hot water chimney

sweep mode

◁ The product now works at maximum load for 15

minutes. If you do not press any buttons for 15

minutes or if a flow temperature of 85 °C is reached,

the chimney sweep function is automatically

switched off.

2. Take the measurements at the earliest after three

minutes of the product operating.

Applicability: VKK 226/4, VKK 286/4, VKK 366/4

▶ Remove the upper casing (→ Installation instructions).

▶ Use the test points that are underneath for the meas-

urement (→ Installation instructions).

Applicability: VKK 476/4, VKK 656/4

1 Flue gas test point 2 Fresh air test point

▶ Use the test points on the adapter for the measure-

ment, as shown.

3. Unscrew the sealing cap from the flue gas test point (1).

4. Remove the sealing cap from the combustion air test

opening (2).

5. Take the measurements in the flue gas route at the flue

gas test point.

6 Troubleshooting

12 Operating instructions ecoVIT exclusiv 0020258609_00

– Immersion depth: ≈ 80 mm

6. Take measurements in the air route on the combustion

air test opening (2).

– Immersion depth: ≈ 10 mm

7. Switch off the chimney sweep function by pressing the

− and + buttons for the DIA system at the same time.

8. Screw the sealing cap onto the flue gas test point (1).

9. Fit the sealing cap onto the combustion air test opening

(2).

Applicability: VKK 226/4, VKK 286/4, VKK 366/4

▶ Install the upper casing (→ Installation instructions).

6 Troubleshooting

6.1 Eliminating faults

▶ Use the table in the appendix to attempt to eliminate

faults.

Troubleshooting (→ Page 14)

▶

Press (max. three times) to restart the product.

▶ If you are unable to eliminate the fault and the fault re-

curs despite reset attempts, contact an approved heating

specialist company.

6.2 Checking the product status

Heizbetrieb - Bren

1 Display 2 i button

1. Call up the product status by pressing the i button.

2. Switch the display back to normal operating mode by

pressing thei button.

7 Decommissioning

7.1 Temporarily decommissioning the product

Caution.

Risk of material damage due to frost

The frost protection and monitoring devices

are only active while the unit is connected to

the power mains, the product is switched on

via the main switch and the gas stopcock is

open.

▶ You must use the control if you want to

activate and deactivate the product in

normal mode.

▶ If no control is present when a main switch

has been switched on, set the rotary

knobs for the target heating flow and

cylinder values to the anti-clockwise end

stop.

▶ Do not disconnect the product from the

power mains when it is in normal mode.

▶ Leave the main switch in position 1 in

normal mode.

1 Main switch

2 Heating flow temperat-

ure rotary knob

3 Cylinder temperature

rotary knob

1. Turn the rotary knob for the cylinder temperature (3)

anti-clockwise as far as it will go.

2. Turn the rotary knob for the heating flow temperature

(2) anti-clockwise as far as it will go.

3. If the fan continues to run, wait until it stops.

◁ "Fan overrun" is shown in the display.

4. Turn the main switch (1) to position 0.

5. Close the gas stopcock and the cold-water isolation

valve.

Note

The isolators are not included in the scope of

delivery for your product. They are installed

on-site by the competent person. Ask the

competent person to explain where the isol-

ators are located and how they are operated.

7.1.1 Draining the heating installation

Another way to protect the heating installation and the

product from frost for very long switch-off periods is to drain

them completely.

▶ Consult a competent person about this.

Recycling and disposal 8

0020258609_00 ecoVIT exclusiv Operating instructions 13

7.2 Permanently decommissioning the product

▶ Have a competent person permanently decommission

the product.

8 Recycling and disposal

▶ The competent person who installed your product is re-

sponsible for the disposal of the packaging.

If the product is identified with this symbol:

▶ In this case, do not dispose of the product with the

household waste.

▶ Instead, hand in the product to a collection centre for old

electrical or electronic appliances.

If the product contains batteries that are marked with

this symbol, these batteries may contain substances that are

hazardous to human health and the environment.

▶ In this case, dispose of the batteries at a collection point

for batteries.

9 Guarantee and customer service

9.1 Guarantee

You can request information on the manufacturer's guaran-

tee from the contact address provided on the back page of

this document.

9.2 Customer service

The contact details for our customer service are provided on

the back page or on our website.

Appendix

14 Operating instructions ecoVIT exclusiv 0020258609_00

Appendix

A Status codes

Note

Since the code table is used for various products, some codes may not be visible for the product in question.

Statuscode Meaning

S.00 Heating: No heat de-

mand

Heating has no heat demand. The burner is off.

S.01 Heating mode: Fan start-

The fan start-up for heating mode is activated.

S.02 Heating mode: Pump

pre-run

The pump prerun for heating mode is activated.

S.03 Heating mode: Ignition The ignition for heating mode is activated.

S.04 Heating mode: Burner

The burner for heating mode is activated.

S.06 Heating mode: Fan over-

run

The fan overrun for heating mode is activated.

S.07 Heating mode: Pump

overrun

The pump overrun for heating mode is activated.

S.08 Heating mode: Anti-cyc-

ling time

The anti-cycling time for heating mode is activated.

S.20 DHW demand The domestic hot water demand is activated.

S.22 DHW mode: Pump pre-

run

The pump prerun for domestic hot water mode is activated.

S.24 DHW mode: Burner on The burner for domestic hot water mode is activated.

S.27 DHW mode: Pump over-

run

The pump overrun for domestic hot water mode is activated.

S.31 No heat demand: Sum-

mer mode

Summer mode is activated; there is no heat demand. The external control blocks heating mode.

S.34 Heating mode: Frost pro-

tection

The frost protection function for heating mode is activated.

B Troubleshooting

Symptom Possible cause Measure

No hot water, heating stays cold No gas 1. Check whether the gas stopcock in the building and the gas

stopcock on the product are open.

2. Open one or both of the gas stopcocks.

Installation isolator is closed 1. Check whether one of the isolators is closed.

2. Ask a competent person whether closed isolators can be

opened again.

No power supply 1. Check whether the power supply to the building and the main

switch on the product are switched on.

2. Switch on the power supply to the building and the main

switch on the product.

The display shows S.39 "Con-

tact thermostat activated" (e.g.

by the condensate pump or the

surface-mounted thermostat in

the underfloor circuit)

1. Clean the condensate pump with clean water in accordance

with the operating instructions for the condensate pump or

contact your approved heating specialist company.

2. Contact an approved heating specialist company.

Filling pressure in the heating

installation too low. F.22"Water

pressure too low" appears in

the display

1. Fill the heating installation. (→ Page 11)

2. If the pressure drops too frequently, contact an approved

heating specialist company. The cause of the loss in heating

water must be established and eliminated.

Appendix

0020258609_00 ecoVIT exclusiv Operating instructions 15

Symptom Possible cause Measure

No hot water, heating stays cold Fault during the ignition pro-

cess. F.28 "No ignition during

start-up" or F.29 "Flame goes

out during operation" appears

in the display. The symbol is

shown in the display.

1. Check whether the gas stopcock is open.

2. If the gas stopcock is closed, open the gas stopcock with the

agreement of an installation company.

3. Press and hold the reset button for one second to cancel

ignition switch-off after three unsuccessful attempts if the

burner has so far failed to ignite.

4. If the product does not start up after three reset attempts,

contact an approved heating specialist company.

Fault in the air/flue gas route

or condensate discharge. F.32

"Speed deviation too great" or

F.50 "Failure Siphon switch"

appears in the display. The

and symbols are shown in the

display.

1. Contact an approved heating specialist company.

Domestic hot water functioning

correctly; heating does not start

Control settings not correct 1. Compare the control settings with the specifications in the

control's operating instructions.

2. Correct the settings in accordance with the operating instruc-

tions for the control.

3. Contact an approved heating specialist company if you en-

counter problems when configuring the settings.

The rotary knob for the heating

flow temperature is not at the

clockwise end stop when the

control is connected

1. Check the setting of the rotary knob for the heating flow tem-

perature when the control is connected.

2. Turn the rotary knob for the heating flow temperature as far

as it will go clockwise.

Heating flow temperature set

incorrectly with no control con-

nected

1. Check the heating flow temperature setting.

2. Set the rotary knob for the heating flow temperature to the

required heating flow temperature with no control connected.

No hot water, heating function-

ing correctly

Control settings not correct 1. Compare the control settings with the specifications in the

control's operating instructions; the rotary knob for the cylin-

der temperature is at the clockwise end stop when the con-

trol is connected.

2. Correct the settings in accordance with the operating instruc-

tions for the control.

3. Contact an approved heating specialist company if you en-

counter problems when configuring the settings.

The rotary knob for the cylinder

temperature is not at the clock-

wise end stop when the control

is connected

1. Check the setting for the rotary knob for the cylinder temper-

ature when the control is connected.

2. Set the rotary knob for the cylinder temperature as far as it

will go clockwise when the control is connected.

The cylinder temperature is

set incorrectly with no control

connected

1. Check the cylinder temperature setting.

2. Set the rotary knob for the cylinder temperature to the re-

quired cylinder temperature with no control connected.

0020258609_00 24.05.2017

Supplier

Vaillant Deutschland GmbH & Co.KG

Berghauser Str. 40 D-42859 Remscheid

Telefon 021 91 18‑0 Telefax 021 91 18‑2810

Auftragsannahme Vaillant Kundendienst 021 91 5767901

info@vaillant.de www.vaillant.de

the manufacturer's written consent.

We reserve the right to make technical changes.

0020258609_00

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vaillant ecoVIT exclusiv VKK 366-4 in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vaillant ecoVIT exclusiv VKK 366-4

Vaillant ecoVIT exclusiv VKK 366-4 User Manual - German - 20 pages

Vaillant ecoVIT exclusiv VKK 366-4 User Manual - French - 20 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vaillant ecoVIT exclusiv VKK 366-4 Manual

Product: