Manual Vaillant ecoTEC plus 837 (page 12 of 16) (English)

602582

Zoom out

Zoom in

1/16

12 Instructions for use ecoTEC

The boiler will now operate automatically to provide cen-

tral heating for the conditions selected on the external

controls (ecoTEC combination boilers will also provide

domestic hot water on demand).

After the boiler stops operating the pump will continue

to operate for a short period to fully disperse the heat

from the boiler.

Note

The boiler incorporates an anti-cycling econo-

miser control to prevent energy wasteful ON

and OFF operation of the boiler for short peri-

ods when in the central heating mode. When

turning the room thermostat to a higher setting

there may therefore be a short delay before the

boiler operates.

4.7 Status displays

bar

iFP

plus pro

Fig. 4.16 Status displays

The status displays provide information on the operating

status of the appliance.

• Press the “i” button (1) to activate the status displays.

The display (2) then shows the current status code, for

example “S. 4” for burner operation. The table below

explains the most important status codes.

In switching phases, for example on starting up again

after the flame was extinguished, the status message

“S.” briefly appears.

• Press the “i” button (1) again to switch the display

back to normal mode.

Display Meaning

Displays during heating operation

S. 0 No heat required

S. 1 Pump running

S. 3 Ignition sequence (heating operation)

S. 4 Burner ignited

S. 6 Fan and pump overrun

S. 7 Pump overrun

S. 8 Anti cycling mode (after heating operation)

S.30 Room thermostat 3/4 no heating demand

S.31 Summer mode active

S.34 Frost protection mode

Displays in hot water operation (ecoTEC combinati-

on boilers only)

S.10 Hot water demand

S.14 Burner ignited

Displays for hot holding operation

(ecoTEC combination boilers only)

S.20 Hot holding request

S.24 Hot burner holding operation on

Displays in cylinder charging mode

(ecoTEC system boilers only)

S.20 Cylinder charging request

S.24 Cylinder charging burner on

Table 4.1 Status codes (selection, a complete set of status

codes can be found in the installation and servicing

manual)

4.8 Troubleshooting

In the unlikely event that a problem occurs with the ope-

ration of the ecoTEC boiler, the following points should

be checked:

Boiler fails to operate:

– Is the gas supply turned on (see 4.3.1)?

– Is the water supply turned on (ecoTEC combination

boilers only, see 4.3.1)?

– Is there enough water in the heating system (see

4.3.2)?

– Is the electrical supply switched ON?

– Is the main ON/OFF control in the “ON” position

(switch position “I”, see 4.4)?

– Is there an ignition problem (see 4.8.2)?

Hot water operates but no central heating (ecoTEC

combination boilers only)

- Is the heating turned ON (see 4.6.1)?

- Are all external heating controls ON (see 4.6.3)?

Caution

Inappropriate modifications can cause damage.

If your boiler still does not operate then please

consult your installer or Vaillant Service

Solutions (0870 6060 777).

4 Operation

I have a Vaillant ecoTEC plus 837. The control panel is quite different to the on line manuals. There is one Contol panel window and 2 sets of +/- buttons below. There is also a small button displaying a flame. The power is on (can hear fan) but NOTHING on the control button.....and NO heating!
Can anyone enlighten/ help me? Submitted on 10-2-2022 at 19:03
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Vaillant ecoTEC plus 837 in the language / languages: English as an attachment in your email.

The manual is 3,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Vaillant ecoTEC plus 837 Manual

Product: