469474
9
Zoom out
Zoom in
Previous page
1/16
Next page
9Instructions for use ecoTEC / 838402_06
h
Note
Your appliance has a pressure sensor.
If the pressure falls below 0.6 bar the pressure
flashes in the display.
If it falls below 0.3 bar the appliance switches
off. The error message F.22 appears in the dis-
play. The system must be filled with water be-
fore you start up the appliance again.
4.4 Turning the boiler ON
1
2
Fig. 4.8 Switching on the appliance (example: ecoTEC plus)
• Use the main ON/OFF control to switch the appliance on.
I: “ON” – 0: “OFF”
When you switch on the appliance, the current operat-
ing status appears in the display (2).
To adjust the appliance according to your requirements,
read sections 4.5 and 4.6, which describe the setting
options for hot water supply and heating.
a
Caution
Risk of damage.
The boiler frost protection and monitoring sys-
tems are only active when the main ON/OFF con-
trol of the appliance is in the “I” position and it is
not disconnected from the main power supply.
4.5 Domestic hot water with ecoTEC combination
boilers
The boiler must only be used when the heating system
contains water (see 4.3.2).
4.5.1 Setting the water temperature
Switch on the appliance as described in section 4.4.
The domestic hot water temperature can be adjusted
using the hot water temperature control (3).
Turn the control clockwise to increase the tempera-
ture and anti-clockwise to decrease the temperature.
This corresponds to:
- left limit approx. 35 °C
- right limit max. 65 °C.
2
3
plus/exclusive pro
Fig. 4.9 Setting the water temperature
h
Note
This control adjusts the maximum domestic hot
water temperature. If adjusting the control up-
wards appears to have no effect on the temper-
ature, then the boiler is already operating at
full output for the selected flow rate.
When you adjust the required temperature, the set
value is shown in the display (2). After five seconds the
display returns to standard mode (the current heating
flow temperature).
a
Caution
If you live in a hard water area please do not set
the control knob (3) above the mid (12 o’clock)
position to prevent excessive scale formation.
4.5.2 Switching the warmstart function on and off
The warmstart system of the ecoTEC combination boil-
ers provides you with hot water at the required temper-
ature immediately. To do this, the hot water heat ex-
changer of the ecoTEC is kept at a pre-selected temper-
ature level and the boiler will therefore periodically op-
erate to maintain this temperature.
ecoTEC plus and ecoTEC exclusive
Activate the warmstart system by briefly turning the
knob (1) all the way clockwise (position a).
Then select the desired hot water outlet temperature
again, e.g. setting b (refer to Section 4.5.1). The appliance
automatically adapts the hot holding temperature to the
set hot water temperature. The tempered water is directly
available at the taps; the symbol
flashes in the display.
Switch off the warmstart system by briefly turning the
knob (1) all the way anti-clockwise (position c). The
symbol
disappears. Then select the required hot
water outlet temperature again, e.g. setting b.
Operation 4
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vaillant ecoTEC exclusiv 146 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vaillant ecoTEC exclusiv 146 in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vaillant ecoTEC exclusiv 146

Vaillant ecoTEC exclusiv 146 User Manual - German - 28 pages

Vaillant ecoTEC exclusiv 146 Manual - Dutch - 2 pages

Vaillant ecoTEC exclusiv 146 User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info