602542
21
Zoom out
Zoom in
Previous page
1/52
Next page
Start-up 6
0020147164_04 aroTHERM Installation instructions 21
6 Start-up
6.1 Run the start-up
1. Before starting up the product, read through the operat-
ing instructions.
2. Check that the electrical partition is installed.
3. Check that the hydraulic and electric connections are
correctly designed.
4. Check that a dirt filter is installed in the heat pump re-
turn.
5. Check whether an expansion relief valve, an expansion
vessel and a pressure gauge are installed.
6. Check the leak-tightness of the connections.
7. Open all the heating circuit valves.
6.2 Heat pump operating concept
Caution.
Risk of material damage caused by incor-
rect handling.
Incorrect settings at installer level may cause
damage to the heating installation.
Only access the installer level if you are
an approved competent person.
The operating concept and operation of the heat pump is
described in the operating instructions for the heat pump.
Menu Installer level
You can call up the installer level using code 17.
6.3 Running through the installation assistant
The installation assistant is launched when the heat pump is
switched on for the first time.
You must confirm the launching of the installation assistant.
Once confirmed, all heating demands from the heat pump
are blocked. This status remains until the installation assist-
ant is completed or cancelled.
Set the system diagram number in the VWZ AI heat pump
control module in accordance with the schematic drawings in
the appendix ( Page 30).
6.3.1 Setting the language
Menu Basic setting Language
You can use this function to set the desired language.
6.3.2 Telephone number for the competent
person
You can store your telephone number in the appliance
menu.
The operator can display it in the information menu. The tele-
phone number can be up to 16 digits long and must not con-
tain any spaces. If the telephone number is shorter, end the
entry after the last digit by pressing the right-hand selection
button .
All of the digits to the right will be deleted.
6.4 Calling up Live Monitor (checking status
codes)
Menu Live Monitor
You can use this function to call up the status code of the
heat pump, which provides you with information about
the current operating condition of the heat pump.
6.5 Calling up statistics
Menu Installer level Test menu Statistics
You can use this function to call up the statistics for the
heat pump.
6.6 Filling the heating circuit
Note
We recommend using ethylene glycol with corro-
sion-inhibiting additives.
If no frost protection has been poured in, the
product will not be protected in the event of a
power cut when there is frost.
Conditions: SW10 open-end spanner
A
B
10mm
2
1
3
4
1 Heating circuit purging
valve
2 Open-end spanner (on-
site)
3 Hose
4 Collecting container (on-
site)
To purge the heating circuit during the filling procedure,
use a filling pump.
Connect one end of the hose (3) to the drain valve.
When purging, insert the other end of the hose (3) into
the mixing container (4).
Open the filling valve using an open-end spanner (2).
To purge the heating circuit, open the purging valve by a
1/4 rotation (B) using an open-end spanner.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Vaillant aroTHERM VWL 55-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Vaillant aroTHERM VWL 55-2 in the language / languages: English as an attachment in your email.

The manual is 3,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Vaillant aroTHERM VWL 55-2

Vaillant aroTHERM VWL 55-2 User Manual - German - 24 pages

Vaillant aroTHERM VWL 55-2 User Manual - Dutch - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info