Manual V-Zug DW-Bora 14 (page 19 of 36) (English, German, Dutch, French, Italian, Portuguese, Spanish)

503575

Zoom out

Zoom in

1/36

for the type of wall).

-Take the upper part of the structure B (Fig.4) and insert the

3 slots onto the 3 screws that are not completely tightened.

Rotate slightly to t (Fig.4). Drive in the fourth screw X and

tighten the remaining 3 to allow denitive blocking of the

upper part of structure B.

-Take the lower part of the telescopic structure C and insert

it into the upper structure B (Fig.5). Adjust the height by

referring to the amounts X indicated in Fig.14 and block it

using the 8 screws G that are supplied (Fig.6).

• Suction version: Fix the exible pipe to the prepared air

evacuation hole (Fig.7).

• Filtering version: Connect the air exhaust pipe to the

recirculation air deectorM, and tighten the screwI, asshown

in Fig.8. The carbon lters must be tted inside the suction

hood as shown in Fig.16. There are two dierent types of

active carbon lters: long-lasting regenerable active carbon

lters (washable) (Fig.17) and standard non-regenerable

active carbon lters (Fig.16).

-Take the upper chimney piece and x it to the structure

using the 2 screws A (Fig.9). Join the lower chimney piece

with the upper one and x it carefully using adhesive tape L

(Fig.10A).

-Unscrew the 2 screws O, max 3 mm (Fig.10A). Insert the

suction unit inside the structure paying attention that the

previously unscrewed screws O, hook into the slots in the

lower part as indicated in (Fig.10B). Drive in the 3 screws N

(supplied) and tighten the 2 screws O (Fig.10B).

-Fix the air evacuation pipe H (not supplied) onto the

connection ange F (Fig.11).

-Remove adhesive tape L and rest the lower chimney piece

above the cooker hood (Fig.12).

-If necessary, x the lower duct to the hood from the inside,

using the screws P (Fig.13).

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before

any food is cooked.We also recommend that the appliance is

left running for 15 minutes after the food is cooked, in order

to thoroughly eliminate all contaminated air.

The eective performance of the cooker hood depends on

constant maintenance; the anti-grease lter and the active

carbon lter both require special attention.

• The anti-grease ﬁlter is responsible retaining the grease

particles suspended in the air, therefore it is subject to

clogging with variable frequency according to the use of the

appliance.

- To prevent the danger of possible res, at least every 2

months one must wash the anti-grease lters by hand using

non-abrasive neutral liquid detergents or in the dishwasher

at low temperatures and on short cycles.

- After a few washes, colour alterations may occur. This does

not give the right to claim their replacement.

• The active carbon ﬁlters are used to purify the air that is

sent back into the room and its function s to mitigate the

unpleasant odours produced by cooking.

- The non-regenerable active carbon lters must be replaced

at least every 4 months. The saturation of the active charcoal

depends on the more or less prolonged use of the appliance,

on the type of kitchen and on the frequency with which anti-

grease lter is cleaned.

- Regenerable activecharcoal ltersmust be washed by hand,

with non abrasive neutral detergents, or in the dishwasher at

a maximum temperature of 65°C (the washing cycle must be

complete without dishware). Remove excess water without

damaging the lter, remove the plastic parts, and let the mat

dry in the oven for at least 15 minutes approximately at a

maximum temperature of 100°C. To keep the regenerable

charcoal lter functioning ecient this operation must be

repeated every 2 months. These must be replaced at least

every 3 years or when the mat is damaged.

• Before remounting the anti-grease ﬁlters and the rege-

nerableactivecharcoal lters it isimportant that they are

completely dry.

• Clean the hood frequently, both internally and externally,

using a cloth dampened with denatured alcohol or neutral

liquid detergents that are non abrasive.

• The lighting .system is designed for use during cooking

and not for the prolonged general lighting of the room. The

prolonged use of the lighting system signicantly decreases

the average duration of the bulbs.

• Attention: The non compliance with the hood cleaning

warnings and with the replacement and cleaning of thelters

entailsrisk of res.One therefore recommendskeeping to the

suggested instructions.

• Replacing halogen light bulbs (Fig.18):

To replace the halogen light bulbs B, remove the glass pane

C using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution: Do not touch the light bulb with bare hands.

• Commands (Fig.19):

The key symbols are explained below:

A = LIGHT

B = OFF

C = SPEED I

D= SPEED II

E = SPEED III

F = AUTOMATIC STOP TIMER - 15 minutes (*)

• If your appliance does not have the INTENSIVE speed

function, press key E for two seconds and it will be activated

for 10 minutes after which it will return to the previously set

speed.Whenthe function is activethe LED ashes.To interrupt

it before the 10 minutes have expired press key E again.

• Clean Air:

By pressing key Ffortwoseconds (with thehoodswitched o)

the “clean air” function is activated. This function switches

the appliance on for ten minutes every hour at the rst speed.

As soonas this function is activated themotor starts up at the

rst speed for ten minutes. During this time key F and key

C must ash at the same time. After ten minutes the motor

switches o and the LED of key F remains switched on with

a xed light until the motor starts up again at the rst speed

after fty minutes and keys F and C start to ash again for ten

minutes and so on. By pressing any key for the exclusion of

the hood light the hood will return immediately to its normal

functioning (e.g. if key Dis pressed the “clean air” function is

deactivated and the motor moves to the 2nd speed straight

away. By pressing key B the function is deactivated).

(*) The “AUTOMATIC STOP TIMER” delays stopping of the

hood, which will continue functioning for 15 minutes at the

operating speed set at the time this function is activated.

• Anti-grease and active carbon ﬁlters saturation:

-After 30 hours of work, the key A ashes every 2 sec.; in that

event,theanti-greaseand activecarbonltermustbecleaned,

if present.

-After 120 hours of work, the key A ashes every 0.5 sec.; in

thatevent,the standard active carbonltersmustbe replaced,

if present.

- 19 -

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of V-Zug DW-Bora 14 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

V-Zug DW-Bora 14 Manual

Product: