Manual UPM WT440H (page 3 of 6) (English, French)

557924

Zoom out

Zoom in

1/6

MOONPHASE

MONDAY

CLOCK1

OUT

TREND

Clock 1 Setting:

Clock 2 Setting:

Press and hold for 3 seconds to enter the clock setting mode. You

will hear a beep. (The CLOCK 1 symbol will appear and the time will blink).

Press to set the hour and to set the minute;

Press during clock setting to change between 12 and 24

hour display. This also will end clock setting.

Press or no key press for one minute will end clock setting.

Scroll to Clock 2 mode using . (The CLOCK 2 symbol will appear).

Press or key to change the hour (in one hour increments/decrements

relative to Clock 1)

MODE

HOUR MINUTE

ALARM/( C/ F)

MODE

°°

CLOCK SETTING

Alarm 1 and Alarm 2 Setting:

Scroll to Alarm 1 using . The ALARM 1 symbol will appear.

Press to set the hour

Press to set the minute

Press to toggle alarm on and off.

When the alarm is set ON, the symbol

will appear and the unit will beep.

In the normal clock display, if the alarm is set ON,

the symbol will also appear on the display.

MODE

HOUR

MINUTE

ALARM

When the Alarm Sounds:

or symbol will blink.

Press to snooze the alarm for 5 minutes.

After that the alarm will sound again.

Press ANY other key to stop the alarm. Or without interruption, the

alarm will automatically stop after one minute.

SNOOZE

To set Alarm 2, scroll to Alarm 2 using .

The ALARM 2 symbol will appear. Follow the same

steps as above to set. In the normal clock display,

if the alarm is set ON, the symbol will also appear

on the display.

MODE

NOTE:BothAlarm1andAlarm2arebasedonthetimesetonClock1.

ALARM SETTING

TROUBLESHOOTING

The remote (outdoor) readout on the receiver is

blinking.

The remote (outdoor) readout on the receiver is

blinking. The receiver will not detect or receive

the temperature and humidity data from the

remote transmitter, even after the Manual Learn

Function has been executed.

The temperature and humidity data on the

remote transmitter does not match the data

displayed on the receiver.

The temperature and humidity data on the

remote transmitter does not match the data

displayed on the receiver.

This may also be the result of a temporary loss of reception due

to interfering sources. Normal reception should resume once

the interference ends. Refer to the WIRELESS TRANSMISSION

section.

Re-synchronize the remote transmitter and receiver by pressing

and holding on the receiver for 3 seconds until a beep is

heard. The temperature and humidity data from the remote

transmitter will display on the receiver within 3 minutes. Refer to

the WIRELESS TRANSMISSION (Manual Learn Function) section.

CHN

Ensure the remote transmitter is away from any possible source of

interference and electrical disturbances. You may try to reposition

the remote transmitter in a different location and/or closer to the

receiver. The remote transmitter does have a maximum range of

40 metres, but any walls or windows the signal has to pass through

will reduce the distance. Due to the nature of the batteries,

extreme cold temperatures may also affect the transmission range.

Refer to the WIRELESS TRANSMISSION section and repeat the

Manual Learn Function with the remote transmitter in a new

location.

This may occur when you move the remote transmitter from one

environment to another. For example, when you bring the

transmitter from inside the warm house out to the cold exterior. In

such a case, there will be a big change in temperature. The

transmitter will record this change in temperature much quicker

than it is able to transmit the data to the receiver (which is done

once every minute). Therefore, you will temporarily get a

difference in reading between the remote transmitter and receiver.

The solution is to allow the remote transmitter some time to sit in

its new location to reach equilibrium. This may take several

minutes. Once the data is stable, the data displayed on the

remote transmitter should match that displayed on the receiver.

PROBLEM

SOLUTION

SPECIFICATIONS

WD633 - WEATHER STATION RECEIVER

- Battery Type: 2 X 1.5V AA batteries

- Operating Temperature: -5

- Temperature Range: -9.9

°C °C

°C t °C

°C °C °C

Resolution: 0.1°C

to 50

o55

- Measurement Accuracy: Max. +/- 1 within measuring range of 0 to 40

WT440H - WEATHER STATION TRANSMITTER

- Battery Type: 2 X 1.5V AA batteries

- Operating Temperature: -20°C to 60°C

- Temperature Range: -30°C to 70°C

- Temperature Resolution: 0.1°C for above -10°C / 1°C for below -10°C

- Measurement Accuracy: Max. +/- 1°C within measuring range of 0°C to 40°C

- Humidity Range: 25% to 90% RH (resolution 0.5%)

- Transmission Frequency: 433.92 MHz

- Transmission Range: up to 40 metres in open area

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,

INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

FCC COMPLIANCE LIMITED TWO-YEAR WARRANTY

UPM warrants this product, excluding battery, to be free from defects in the materials or workmanship, under normal

use and service, for a period of two years from the date of purchase by the consumer.

If, at any time during the warranty period, the product is defective or malfunctions, UPM shall repair or replace it (at

UPM's discretion) within a reasonable period of time.

If the product is defective,

(i) return it, with a dated proof of purchase, to the retailer from which you purchased it, or

(ii) package it carefully, along with a dated proof of purchase and a short description of the malfunction, and mail it,

postage prepaid, to the following address:

UPM Marketing Inc.

Return Goods

Unit 10B - 250 Shields Court

Markham, Ontario

L3R 9W7

This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by UPM that

the defect or malfunction was caused by damage which occurred while the product was in the possession of the

consumer.

UPM's sole responsibility shall be to repair or replace the product within the terms stated above. UPM SHALL NOT BE

LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY

OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY UPM MAKES ON THIS PRODUCT. THE DURATION OF ANY

IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, IS HEREBY LIMITED TO THE TWO YEAR DURATION OF THIS WARRANTY. Some states do not allow

limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

This warranty gives you specific legal rights, and you may have other rights which may vary from state to state.

If you have any questions concerning this warranty, please write to:

UPM Marketing Inc.

Customer Service Department

Unit 10B - 250 Shields Court

Markham, Ontario

L3R 9W7

Or call 1-888-GO-TO-UPM (1-888-468-6876), Monday to Friday, from 9:00am to 5:00pm eastern.

(2)

CUSTOMER SUPPORT HOTLINE: 1-888-468-6876

MOON PHASE

Moon Phase Display

MOON PHASE DISPLAY

The moon phase is automatically updated according to the calendar setting.

New Moon

Young Crescent

First Quarter

Waxing Gibbous

Full Moon

Waning Gibbous

Last Quarter

Old Crescent

ALARM 1

MONDAY

CLOCK1

MONDAY

CLOCK1

Alarm 1 Setting

Clock Display

PAGE 7

PAGE 16

PAGE 8

PAGE 17

PAGE 9

PAGE 18

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of UPM WT440H in the language / languages: English, French as an attachment in your email.

The manual is 0,94 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

UPM WT440H Manual

Product: