Manual Unold 8690 (page 29 of 132) (English, German, Dutch, French, Italian, Spanish)

379923

Zoom out

Zoom in

1/132

the Functions oF the Breadmaker

Alarm function

The alarm sounds:

 whenever an active button is pressed,

 during the second kneading process, to remind you to add

seeds, fruit, nuts or other ingredients. Please note that this

function cannot be deactivated, e.g. in the time preset

function,

 at the end of the baking process, the appliance beeps often

during the keep-warm phase,

 at the end of the keep-warm phase 10 beeps remind you

that the appliance is now switched off and the bread has to

be taken out of the bread pan. Please note that this function

cannot be deactivated, e.g. in the time preset function.

Repeat function after power outage

Should the electricity supply been cut off during the operation

of the Breadmaker, the appliance will re-start, on re-instatement

of the supply, automatically from the point arrived at when the

cut-off occurred as long as the interruption is not longer than

2 minutes. If the interruption in the electricity supply lasts

more than 2 minutes and the display shows the basic setting,

the Breadmaker must be re-started. This is only practical if the

dough was not further than the kneading phase when the break

occurred. If the program was already in the last rising cycle when

the power broke down and the interruption lasts over a longer

time, the dough cannot be saved and the program has to be

started again.

Safety functions

The lid should not be opened after the program has started, except

during the second kneading phase for adding of ingredients.

During the rising and baking phase the lid should never be opened,

as the bread may sink down.

If the temperature in the appliance, due to previous use, is too

high (above 40 °C) for a newly chosen program, when an attempt

to re-start is made, the display will show H:HH and an alarm

sound will be heard. Should this occur, remove the pan and wait

until the appliance has cooled off and is back to the beginning of

the originally chosen program.

Please not that the breadmaker has no top heating for safety

reasons, so the crust will be lighter on top and darker at the sides

and bottom of the bread. For safety reasons an additional top

heating is not allowed.

If after pressing START/STOP, E:EE is shown in the display,

the temperature control is defective. In this case please send

the appliance to our technical service (address see Warranty

Conditions).

EIGENPROGRAMM/USER PROGRAM

In addition to the other numerous programs provided by the

BACKMEISTER

you can also program your own USER PROGRAM.

You can change the basic time and program phase settings as

programmed at the factory or leave out various program phases.

This allows you to develop your own individual program for baking

bread or preparing dough. Below you will find a sample recipe.

First you should become familiar with the following information

on the basic programming and use of the USER PROGRAM.

USER PROGRAM

The program features the following options

Browning programmable

Timer programmable

Loaf size I and II not programmable

The default program is the same as for the BASIC program.

Phase Preset Programmable time frame

Total time 3:10 hours

Knead 1 12 minutes 0-14 minutes

Rise 1 18 minutes 0-100 minutes

Knead 2 15 minutes 0-15 minutes

Rise 2 85 minutes 0-100 minutes

Rise 3 OFF/AUS 0-120 minutes

Bake 60 minutes 0-70 minutes

Keep warm 60 minutes OFF/60 minutes

The times can be programmed as shown in the table.

Proceed as follows:

Select the USER PROGRAM with the Menu button.

Select the desired phase with the ABSCHNITT button. Knead

1 and the programmed time 0:10 for this phase appear on the

display.

The time can be changed by means of the ZEITWAHL button.

Press it repeatedly until the desired time appears on the display

(past OFF, if necessary).

Confirm the change with the ABSCHNITT button. Press this

button again and the next program phase and the programmed

time will appear on the display: Rise 1 = and 0:20.

If the maximum programmable time for the respective program

phase is exceeded by pressing the ZEITWAHL button, O will

appear on the display if this is possible according to the above

table. This phase is then skipped during the program.

Every programmed setting must be confirmed by pressing the

ABSCHNITT button, so you can continue programming the next

program phase.

Once you have programmed all phases to suit your preferences,

conclude the programming by pressing the ABSCHNITT button

and then the START/STOP button. The programmed time for the

user program appears on the display. The program then starts

either immediately or after the time set via the timer function.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Unold 8690 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 1,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Unold 8690 Manual

Product: