Manual Unold 78131 (page 18 of 64) (English, German, Dutch, French, Italian, Spanish)

485044

Zoom out

Zoom in

1/64

15. Make sure that the lead cable does not hang

over the edge of the worktop or table, since

this can cause accidents, for example if

small children pull on the cable.

16. Route the lead cable so that it is prevented

from being pulled or tripped over.

17. Never wrap the lead cable around the

appliance.

18. Always disconnect the lead cable from the

wall socket pulling on the plug, never on the

cable.

19. Before connecting the appliance to the

mains, make sure that the ON/OFF switch is

in OFF position.

20. Do not use the appliance with accessories

of other manufacturers or brands, to prevent

damage.

21. Use the mincer only indoors.

22. Never leave the mincer unattended. Keep

the appliance out of reach of children. The

mincer must not be used by children.

23. When transporting the appliance carry it

with both hands at the motor block – not at

the feed pan or the mincer.

24. Never push the food into the feeding tube

with your fingers. Always use the feedstick

for this purpose. Risk of injuries!

25. In order to avoid food blocking the feeding

worm, do not fill in with excessive pressure,

but only slightly.

26. If the food gets stuck in the feeding worm,

press the reverse button II for a few seconds

to remove the blocking.

27. If the appliance gets repeatedly blocked,

disconnect the appliance from the mains.

Open the worm housing and remove the

obstacles. Then reassemble the appliance

and continue to process the respective food.

When switching over from I to O or to II, wait

a few seconds until the motor has stopped.

28. The mincer must only be used to mince

meat, fish, and vegetables. Do not mince

hard parts such as bones, or nuts. Do not

mince hard-fibre foods such as ginger etc.

29. Disconnect the appliance from the wall

socket after use and prior to cleaning. Never

leave the appliance unattended when it is

connected to the wall socket.

30. Let the appliance cool off before cleaning

it.

31. Never open the casing of the mincer. There

is danger of electric shock.

32. Check the appliance, the wall socket and

the lead cable regularly for wear or damage.

In case the lead cable or other parts appear

damaged, please send the appliance or the

base to our after sales service for inspection

and repair (for address, see warranty terms).

Unauthorised repairs can constitute serious

risks for the user and void the warranty.

The manufacturer will not be liable in the event of incorrect assembly, improper or incorrect use or if

repairs are carried out by unauthorized third parties.

aSSEmBLy OF tHE mInCEr

The switch of the mincer must be in the OFF position before the appliance is connected to the

mains!

1. Remove all packaging materials and any

transport safety devices.

2. Clean all parts with a damp cloth, as

described in the chapter “Cleaning and

maintenance” on page 19.

3. Check if the appliance is switch off.

4. Place the motor block on a solid and flat

surface. The switch has to be on the front

side. Do not cover the ventilation openings

in the bottom.

5. Insert the feeding worm into the worm

housing. The tooth wheel at the end of the

feeding worm should be greased after each

cleaning with a greasing agent admitted for

contact with foodstuff.

6. Place the knife on the axle of the worm. The

flat side of the knife must faces the outside

(mincing plate), the rounded side the inside

(feeding worm). If not correctly installed,

the meat cannot be minced properly.

7. Place the required mincing plate onto the

knife. The small arresting tab at the inner

side of the worm housing must fit exactly

into the little recess of the mincing plate.

8. Firmly screw on the closing ring while

holding the mincing plate in place. Do not

overtighten.

9. Place the mincer head in the opening of

the motor block. The feeding tube faces the

user. Press the locking button down and fix

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Unold 78131 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,62 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Unold 78131 Manual

Product: