573392
125
Zoom out
Zoom in
Previous page
1/130
Next page
121
IX. WARNING MESSAGES
The programmed messages are displayed under certain specific conditions. In the auto preset
condition, the default messages "WARN MESSAGE# xx" are displayed.
WM-#1 PRINTER ERROR
Turn the power off and perform the initial reset operation. Refer to the same section of the programming manual.
WM-#2 INPUT FIGURE OVER LIMITATION
Press CL key. (PLU HALO can be released temporarily by using HALO RELEASE key)
WM-#3 CLERK IS NOT SIGNED ON
WM-#4 ITEM OR MEDIA (SLIP) VALIDATION IS COMPULSORY
Print item or media validation by MISC. VALID key.
(can be released temporarily by using OFF COMPULSORY key)
WM-#5 TOTAL (SLIP) VALIDATION IS COMPULSORY
Print total validation by TTL. VALID key.
(can be released temporarily by using OFF COMPULSORY key)
WM-#6 VALIDATION PAPER HAS NOT BEEN INSERTED INTO ECR
(displayed when the factory optional validation sensor has been installed)
WM-#7 VALIDATION PAPER HAS NOT BEEN REMOVED FROM ECR
(displayed when the factory optional validation sensor has been installed)
WM-#8 MESSAGE INPUT IS COMPULSORY
(can be released temporarily by using OFF COMPULSORY key)
WM-#9 PERFORM FOREIGN CURRENCY SUBTOTAL DISPLAY OPERATION
Press F.C. SBTL key and F.C. MEDIA key.
WM-#10 NUMBER OF PERSONS INPUT IS COMPULSORY
(can be released temporarily by using OFF COMPULSORY key)
WM-#11 SBTL KEY DEPRESSION IS COMPULSORY BEFORE TENDERED AMOUNT INPUT
(can be released temporarily by using OFF COMPULSORY key)
WM-#12 TAX TABLE IS NOT PRESET
Enter tax amount manually. Preset tax table.
WM-#13 TENDERED AMOUNT INPUT IS COMPULSORY
(can be released temporarily by using OFF COMPULSORY key)
WM-#14 DRAWER IS OPEN
This message is displayed only when the optional 'drawer open sensor' is being used.
WM-#15 CASH DECLARATION IS COMPULSORY
(can be released temporarily by using OFF COMPULSORY key)
WM-#16 REGISTRATION BUFFER IS ALMOST FULL
Prepare to close the transaction.
WM-#17 PLU STOCK IS ZERO OR NEGATIVE
Enter stock by programming. Displays only if programmed.
(can be released temporarily by using HALO RELEASE key)
WM-#18 JOURNAL PAPER NEAR END
Replace with new paper roll. When the printer stops during transaction, press X2 key to start printing after the
paper has been replaced.
(only at the beginning of transaction, it can be released temporarily by using OFF COMPULSORY key)
WM-#19 ECR TO ECR RAM DATA TRANSFER ERROR
Check the cable connection between ECR & ECR. Refer to INTERFACES & PERIPHERALS MANUAL for
details.
WM-#20 CLERK INSERT KEY IS REMOVED
Insert previously removed clerk insert key.
WM-#21 SLIP PRINTER IS BUSY
Press CL key and wait for the printer to be ready. Press 'PRINT' on the printer to proceed with the slip.
WM-#22 RECEIPT PAPER NEAR END
Replace with new paper roll. When the printer stops during transaction, press X2 key to start printing after the
paper has been replaced. It is displayed only when the 'receipt paper near end sensor' (factory option) is being
used. (only at the beginning of transaction, it can be released temporarily by using OFF COMPULSORY key)
WM-#23 RECEIPT PAPER END
While the paper is replaced, only RPF key can be pressed. Press X2 key to start printing.
It is displayed only when the 'receipt paper near end sensor' (factory option) is being used.
WM-#24 JOURNAL PAPER END
While the paper is replaced, only JPF key can be pressed. Press X2 key to start printing.
WM-#25 NOT USED
125


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Uniwell SX-330 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Uniwell SX-330 in the language / languages: English as an attachment in your email.

The manual is 0,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info