576638
12
Zoom out
Zoom in
Previous page
1/87
Next page
9
ULGD 350 A1
GB
IE
Preparing for cold lamination
IMPORTANT
After hot laminating, allow the laminator to cool down completely before
beginning with cold lamination. Bear in mind, the rollers inside the laminator
will still be hot. This could damage the laminating pouch and the document
to be laminated!
If not already done: Insert the document support into the two openings
under the pouch ejector slot , such that it is seated fi rmly on the appliance.
Insert the plug of the laminator into a mains power socket.
Switch the appliance on by placing the selector switch for hot and cold lami-
nation
5
at "Cold". The red indicator light Power
3
and the green indicator
light Ready
2
glow.
Place the pouch thickness switch
4
at the corresponding pouch thickness
(see also chapter Switching levels).
Place the document to be laminated into a laminating pouch of the appropriate
size.
NOTICE
Ensure that all edges of the document have at least two millimetres of space
to the edges of the laminating pouch, as shown in Fig. 1 (see p. 8).
Make certain that you use only one pouch for laminating. First open it up,
as shown in Fig. 2 (see p. 8).
For further information about the lamination process, please read the section
Lamination process.
Lamination process
Place the pouch centrally between the two A4 markings and with the closed
side towards the pouch slot
6
and on the supporting surface.
Slide the pouch slowly and straightly into the pouch slot
6
.
When you have slid the pouch several centimetres into the slot
6
it will then
be pulled in automatically. Release the laminating pouch as soon as you
notice it being pulled in automatically.
IMPORTANT
Ensure that there is at least 30 cm of free space behind the laminator.
Otherwise, the pouch will not be ejected completely from the laminator
after lamination. This could damage the pouch.
The fi nished and laminated pouch is ejected from the pouch ejector slot
of the laminator.
IB_100158_ULGD350A1_LB3.indb 9 02.07.14 13:40
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for United office ULGD 350 A1 - IAN 100158 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of United office ULGD 350 A1 - IAN 100158 in the language / languages: English, German, Dutch, Danish, Swedish, Finnish as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info