585461
17
Zoom out
Zoom in
Previous page
1/48
Next page
17 English
INSTALLATION
SETTING UP THE MAIN UNIT (RECEIVER)
BATTERY INSTALLATION
Slide to open the battery door , install 6 pieces of
AA batteries according to the polarity indicated and
close the battery door .
LOCAL WEATHER FORECAST & PRESSURE
SETTING
A pressure sensor is built in the main unit to provide
local pressure reading & local weather forecast back-
up. After battery installation, the main unit will enter
pressure setting mode in the following sequence.
Pressure unit (mb / hPa or inHg) > Current sea level
pressure > Current local weather condition > Exit
The corresponding icon will flash. Press [] 5 or
[] 6 to select, press [BARO] 8 to confirm each
setting.
Note:
Please check the current sea level pressure rea-
ding of your location from weather web site.
Please select current weather condition of your
location between sunny, partly cloudy, cloudy,
rainy or stormy.
You may also enter the local weather forecast &
pressure setting any time by holding the [BARO]
8
button for 3 seconds. (Details also refer to the
“BAROMETRIC PRESSURE & LOCAL WEATHER
FORECAST” section).
r
Sunny Partly Sunny Cloudy Rainy Stormy
SETTING UP THE REMOTE SENSOR
BATTERY INSTALLATION
Loosen the screws
on the battery door with a small
screw driver, insert 2 pieces of AAA batteries according
to the polarity indicated. Replace the cover and tighten
the screws
after the RF setting below.
ESTABLISH RF CONNECTION WITH MAIN UINIT
• Place the main unit away from metal & source of
interference such as mobile phones, appliances,
TV etc.
• For the first installation, turn on the main unit and
then the remote sensor. Set Channel 1 for the first
remote sensor . Set channel 2 and channel 3 for
the 2nd and 3rd sensor (W186-F – 313505.00).
• Hold [CHANNEL/SEARCH] button on main unit
until a beep is sound to search for remote sensor.
The corresponding channel number on the display
will flash indicating it is in the searching mode.
• Press the [Tx] button inside the battery com-
partment of remote sensor to transmit RF signal.
• When RF connection is established, the respec-
tive temperature of the selected channel (A) will
appear on the main unit.
• Replace the cover and tighten the screws on the
remote sensor.
Note: Additional sensor (W-186F – 313505.00) fits
for several weather stations and is able to gauge
temperature and humidity. The main unit (W194-1)
displays the temperature only.
USB TRANSMITTER & PC PROGRAM
INSTALLATION
BATTERY INSTALLATION & USB CONNECTION
• Slide to open the battery door on the bottom
of the USB transmitter, insert 2 pieces of AAA
batteries according to the polarity indicated.
Close the battery door.
• Connect USB transmitter to your PC via an USB
port.
PC PROGRAM INSTALLATION
• Before installation, ensure that
1) Your PC is connected to the Internet. Try
browsing through a couple of websites to
make sure.
2) You are using Windows 2000 XP, Vista or
Windows 7.
3) USB transmitter is connected properly to your
PC via the USB port.
• Insert CD into your CD ROM and double click the
“INSTALL_1940.EXE” or ”NIS01_ INSTALL_1940.
EXE” program to start installation. If the instal-
lation program detected that Microsoft .NET
Framework 2.0 driver was not installed in your
Windows before, it will prompt you to install the
driver. Follow the instruction to install the driver
and complete the rest of the installation.
313500.00_W194-1_Manual.indd 17 15.06.12 11:19
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Unitec W194-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Unitec W194-1 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 4,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info