Manual Uniprodo Uni Pools 17 (page 8 of 33) (English, German, Dutch, French, Italian, Polish, Spanish)

778984

Zoom out

Zoom in

1/33

• Remove the lter cover.

• The lter should be rinsed with water, e.g. from

a garden hose, and it can be re-installed in the

device. If the lter is discoloured or has dirt that

cannot be removed, replace it with a new one.

• Put the cover on the lter.

• Screw the lter to the pool wall.

Draining the water

• Disconnect the device from the power supply.

• Make sure that the hole in the oor on the inside

of the pool is closed.

• Open the water outlet on the outside of the pool.

Connect one end of the hose.

• Open the hole plug on the inside of the pool, the

water will ow out through the hose.

3.3. DEVICE USE

Powering the device

The device is equipped with a power cord with

a residual-current device (circuit breaker). The circuit

breaker should be tested regularly. For this purpose,

reset the switch by pressing the Reset button. Start any

of the jacuzzi functions, e.g. air bubbles, and then press

the TEST button. The switch should cut o the power

supply from the device. Press the RESET button again to

return to the normal operating mode.

PLEASE NOTE: If, after pressing the TEST button, the

switch does not cut o the power supply from the

device, immediately stop using the jacuzzi and contact

the manufacturer‘s service department.

Water ltration function

• Press the ltration On/O button. The device will

begin to lter, the diode will light on the button.

• Pressing the ltration On/O button again will

turn o the ltering process, the LED on the

button will go o.

• When the lter pump runtime exceeds 168 hours,

„FC“ will appear on the display and a signal will

be displayed. This will be information about the

need to replace or clean the lter. The LED on the

lter button will be lit, but the ltering itself will

be turned o. Other device systems will also not

work. To turn o the message, press the ltration

On/O button, the current water temperature

will appear on the display. To restore the ltration

system activity, replace or clean the lter.

Massage function with air bubbles

• Press the On/O button for the air bubbles. The

device will start to spray air into the water in front

of the nozzles, the diode will light on the button.

• Do not activate the function if a cover is placed

on the pool.

• Pressing the bubbles On/O button again will

turn o the bubble release process, the LED on

the button will go o.

• The nozzle system automatically stops working

after 20 minutes. To restart the function, wait 10

minutes.

• For the rst 15 minutes of the function it can be

turned o and turned on without interruption.

After the time of 15 minutes has elapsed after

switching o the air bubble function, wait 10

minutes before turning it on again.

Water heating function

• Press the On/O button to heat the water. The

device will start to heat up the water, the diode

will light on the button. It will also light up the

diode on the ltering On/O button. The device

will also start ltering the water.

• After reaching the set temperature (temperature

setting is described in the next section), the

device will automatically switch o the heating

and ltration of water. The LEDs on the buttons

will go o.

• When the water temperature drops 2°C below the

set value, the heating system and ltration will

start working again.

• Pressing the On/O button again switches o the

water heating process, the LED on the button will

go o.

Setting the water temperature

• Press the entry button to set the temperature, the

display will ash.

• Use the buttons to increase or decrease the

temperature value to set the preferred value.

• Press the input button again to set the

temperature to conrm the entered value.

1. The water heating process depends on

the initial water temperature and external

conditions and it takes around 12-24h.

For a water with temperature of 15°C (tap

water), in ideal conditions, heating time will

take 15h to increase the water temperature

up to 30°C.

2. The heater is mainly used to maintain the

water temperature, we recommend lling

the jacuzzi with warm water.

3. The product with clear signs of use, water or

dirt residues is not subject to return.

• After draining all the water, activate the air

bubbles release function for about 2-3 minutes to

get rid of water from the tubes in the device.

• When nished, disconnect the hose and close the

holes with the plugs.

Storage

• Completely drain the pool water. Remove the

lter.

• After draining the water, dry the pool with a dry

cloth and leave it to dry for 24 hours until it is

completely dry.

• Release the air from the pool by opening the

outlet and air valve, then fold it into the box.

Using the repair kit

• If the product gets torn or breaks, use the

provided repair kit.

• Clean and dry the area of damage. Cut out the

patch.

• Apply the adhesive to the patch, then gently

fasten it to the damaged area.

• Smooth the surface to remove air bubbles.

3.4. CLEANING AND MAINTENANCE

a) Before each cleaning, adjustment, replacement

of accessories and if the device is not used, it is

necessary to pull out the mains plug.

b) Use cleaners without corrosive substances to clean

each surface.

c) Contaminants may be deposited on the walls of the

pool. To clean them, use a mild soap and water.

d) After cleaning the device, all parts should be dried

before reusing it.

e) Store the unit in a dry, cool place, free from moisture

and direct exposure to sunlight.

f) Regular inspections of the device must be carried out

in terms of its technical eciency and any damages.

g) Use a soft cloth for cleaning.

Keeping water clean

• In order to keep the device in good condition and

not to expose yourself and other users to health

problems, you should regularly clean the water in

the pool.

• Water should be periodically cleaned with

chemicals or replaced with fresh water. It is

forbidden to use chemicals with calcium ions.

• When using chemicals, follow the

manufacturer‘s recommendations and

instructions for use, and consult with local

authorities regarding the permissible use of these

products

• Replace and clean the lter regularly. It is

recommended to clean the lter after every 72-

120 h of use. The lter should be replaced once

a month depending on the intensity of use.

• The pH of the water should be maintained at 7.2-

7.8, total alkalinity between 80 and 120 ppm, free

chlorine between 3 and 5 ppm. It is recommended

to use special tests to check the water status.

Tests should be used in accordance with the

recommendations and instructions of their

manufacturer.

Cleaning the lter

• Disconnect the device from the power supply

• Unscrew the lter from the pool wall.

EN 1514 EN

18.01.2022

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Uniprodo Uni Pools 17 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 1.07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Uniprodo Uni Pools 17 Manual

Product: