Manual Uniprodo UNI HEATER 03 (page 7 of 33) (English, German, Dutch, Danish, French, Italian, Polish, Spanish)

779233

Zoom out

Zoom in

1/33

1312

16.11.2020

3.3.5. SETTING THE STARTUP TIME

You can set the time for automatic activation and

operation of the device. To do this, when the device

is in the standby mode, press the timer button on the

control panel (6) or on the remote control (2). After

setting the time in the range of 0-12 hours, the device

will display the set time until automatic start-up and the

timer indicator (8) will light up – this time will be counted

down and after it has expired, the device will start

automatically. The default heating temperature is 23 oC.

CAUTION: if the heating temperature has not been

set and no operating mode has been programmed,

the device will automatically turn off after 12 hours of

continuous operation.

3.3.6. PROGRAMMING THE OPERATING MODE

CAUTION: this operation can only be programmed

using the remote control!

A. Setting the time and day of the week.

In the standby or operating mode, set the time and

day of the week. Press the "SET" button (3) and

the display will show "12" as the default hour. Use

the parameters increasing or decreasing buttons

(5) to set the current hour, then by pressing the

"SET" button (3) to accept the set hour to go to the

minutes setting. The minutes are also set with the

same buttons (5) and conrmed with the "SET"

button (3). After setting the time, the weekday

"d1" will appear, which is Monday by default. Use

the parameters decreasing or increasing buttons

(5) to set the current day of the week ("d1" – "d7"

respectively Monday–Sunday), and then press

the "OK" button to conrm the settings. The time

setting range is 00–23 hours and 00–59 minutes.

CAUTION: the device must be reset after power is

removed. Then use the „SET“ button (5) to check if the

time and day of the week are correct.

B. Blowing temperature setting

During operation, press the parameter

decreasing/increasing button (5), the display will

show „23“ as the default heating temperature.

If necessary, use the same buttons (5) to set the

desired temperature (in the range of 10–49 oC),

and conrm it with the „OK“ button (5).

C. Setting the weekly operation mode.

After previous setting of the time and day of the

week, you can program the weekly operation

mode of the device.

a) Press the ON/OFF button on the device‘s panel (4)

or remote control (1) to start the device.

b) Press the program selection button (8) to enter the

weekly program settings – the program indicator

will light on the display.

c) Press the button for setting the day of the week

(7) on the remote control, and after displaying

the default day „d1“ (Monday) set the current

day by pressing the same button (according to

the diagram: („d1“ – „d7“ respectively Monday–

Sunday) as necessary.

Message D1 D2 D3

Day of

the week Monday Tuesday Wednesday

Message D4 D5 D6 D7

Day of

the week Thursay Friday Saturday Sunday

d) Press the time of day edit button (10) on the

remote control, the display will show „P1“. By

pressing the same button again, we can choose

one of the six times (P1–P6) for a given day with

the setting of any time and temperature.

e) Press the ON time setting button on the remote

control (9), the display will show „00“. The next

pressing of the same button increases the time of

starting the device by one hour, etc. according to

this scheme - the time range from 00 to 24 can

be selected. For example, in the picture below,

turning on at 7:00:

On the back of the remote control, remove the

protective coating of the battery (1) – to do this, pull it

out of the battery compartment (2) by pulling it towards

you (3).

CAUTION: if the protective coating is not removed

despite the ecient battery, the remote control will not

work!

INSTALLATION/REPLACEMENT OF THE REMOTE

CONTROL BATTERY

Symptoms of a depleted remote control battery include

weak or no response to the buttons on the remote. To

remove the battery compartment, press and hold the

compartment lock (5), and with the help of a ngernail

or a sharp object, lift the battery compartment and pull

it towards you away from the remote control (4).

CAUTION: When installing batteries in the remote

control, pay attention to the correct polarity.

3.3. DEVICE USE

3.3.1. STANDBY MODE

After installing the device on a vertical wall, connect the

plug to the power source and then set the switch on

the side of the device (1) to the ON – „I“ position. The

message „S“ will appear on the display, which means

that the device is in the standby mode, i.e. ready for

operation.

3.3.2. TURNING ON/OFF THE DEVICE

Press the ON/OFF button on the device control panel

(4) or remote control (1) to turn on the device. It will

automatically switch to a blowing mode, and the display

will show the message „- -“

3.3.3. SETTING THE HEATING POWER

Press the heating power selection button on the control

panel (5) or on the remote control (4) to select one of

the two heating settings. Default setting „I“ – 1000 W.

Pressing the same button again changes the power

to „II“ – 2000 W. The appropriate selection is signaled

adequately by one or two lights on the device control

panel (2).

3.3.4. SETTING THE TIMER

The timer function counts down the device operating

time until it is automatically turned o, i.e. it enters the

standby mode. Available hours range: 0-12. Press the

timer button on the control panel (6) or on the remote

control (2), the display will show the current time. Each

press of the timer button increases the operating time

of the device by one hour. After selecting the desired

operating time, it will be shown on the display for

about 5 seconds, followed by the timer indicator on

the display, and the display itself will show the previous

parameter.

38,5cm

180cm min

Below is an example of setting 9:30 for Wednesday:

f) Press the switching-o time setting button (11)

on the remote control, the device will show the

default switching-on time on the display. The

switching-o time is set in a similar way as in the

case of setting the switching-on time (selectable

time range from 00 to 24), with the dierence

that the specic time is selected using the o time

button (11) on the remote control.

CAUTION: the time of automatic switching o

of the device cannot be earlier than the time of

switching on! If the hours are the same, the device

goes into the standby mode – yes.

g) Use the parameter increasing/decreasing buttons

(5) to set the desired temperature (within the

range of 10–49 oC).

h) By repeating steps c)–g) you can set the operating

parameters for each day of the week.

i) Press the „OK“ parameter conrming button (5)

on the remote control to nish programming.

CAUTION: when working in the programmed

mode, by pressing the button for setting the

day of the week on the remote control (7), you

can enter the settings for a given day and then

using the program editing button (10) to check the

automatic start time, and by pressing the same

button again, the automatic stop time.

j) To cancel the weekly program mode, press the „P“

button (8) on the remote control.

3.3.7. ACTIVATION/DEACTIVATION OF THE OPEN

WINDOW DETECTION

After turning on the device, press the button for the

open window detection function (6) on the remote

control using the ON/OFF button (on the control panel

4 or on the remote control 1). Indicators (7) and (9) will

light up on the display of the device. The display will

show the default temperature „23“. This temperature

can be changed with the parameter decreasing/

increasing buttons (5). If the device detects a drop

in room temperature, it will stop working. To switch

the device back on, press the ON/OFF button (on the

device panel 4 or on the remote control 1). Pressing the

button for the open window detection function (6) again

deactivates it – the function indicator on the display (7)

turns off.

ENEN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Uniprodo UNI HEATER 03 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 1.07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Uniprodo UNI HEATER 03 Manual

Product: