652321
7
Zoom out
Zoom in
Previous page
1/56
Next page
7
General Information
1.8 - WATER TREATMENT
The chemical-physical characteristics of the filling water and
reinstatement water in heating systems are of fundamental
importance for guaranteeing correct and safe boiler operation.
Before filling the CH circuit with water, it is necessary to analyse
the water and decide for a proper treatment.
The purpose of this treatment is finalized to eliminate or sub-
stantially reduce the following problems:
- lime scale deposit
- corrosions
- deposits
- biological growths (moulds, bacteria, algae, fungi, etc)
The chemical treatment of the network water enables the
prevention of these problems and guarantees safe boiler
operation and economical advantages, in terms of mainte-
nance and global thermal efficiency.
The chemical analysis of the water enables us to obtain a lot
of information on the system’s condition and state of “health”.
It is essential to avoid any problems with the boiler.
The pH is a measure of the acidity or alkalinity of a solution.
The pH scale has a range of 0-14, where 7 is neutral.
Values inferior to 7 indicate acidity, values above 7 indicate
alkalinity.
The ideal pH value for water in heating systems fitted with
aluminium boilers is between 6,5 and 8, with a hardness
of 15°F.
In heating systems where the water has a value outside this ran-
ge, this considerably accelerates the destruction of the protective
oxidized layer which naturally develops inside the aluminium
bodies: if the pH is below 6, acidity is present, if it is above 8,
the water is alkaline or it is caused by an alkaline treatment (for
example phosphate or glycol used as an antifreeze) or in several
cases it is due to the natural formation of alkaline in the system.
Vice versa, if the pH value is between 6,5 and 8, the aluminium
surfaces of the boiler body are passivated and protected from
further corrosive attacks.
To minimize corrosion it is essential to use a scale inhibitor,
however in order for this to function correctly, the metallic
surfaces have to be clean.
The best corrosion inhibitors on sale also contain a pro-
tective system for aluminium which acts by stabilizing the
water’s pH value, preventing unforeseen variations.
We recommend that the heating system’s water pH value is
systematically controlled (minimum twice a year). In order
to do this, it is not necessary to run a chemical analysis in a
laboratory, but it is sufficient to use a simple analytical ‘kit’
contained in portable cases, easily found on sale.
Therefore, prior to filling the heating system with water it will be
necessary to fit the devices indicated in the figure below.
THE CONNECTION MUST BE FITTED ON THE
PRIMARY CIRCUIT’S RETURN PIPE DOWN-
STREAM OF THE CIRCULATING PUMP
All the necessary precautions must be taken in order to avoid
the formation and localization of oxygen in the system’s water.
For this reason, the plastic pipes used in underfloor heating
systems must be impermeable to oxygen.
If any antifreeze solutions are used ensure yourself that they are
compatible with aluminium and with any other components and
materials fitted on the system.
WARNING!
ANY DAMAGE CAUSED BY THE BOILER,
DUE TO THE FORMATION OF LIME SCALE
OR DUE TO CORROSIVE WATER WILL INVA-
LIDATE THE APPLIANCE WARRANTY.
1. Ball valve
2. Inspection pocket
3. Filling-up group
4. Disconnector
5. Scale reducing device
6. Litrecounter
(recommended)
7. “Y” filter
EXAMPLE OF SCALE REDUCING DEVICE CONNECTION FOR WATER TREATMENT
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Unical MODULEX EXT 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Unical MODULEX EXT 100 in the language / languages: English as an attachment in your email.

The manual is 8,87 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Unical MODULEX EXT 100

Unical MODULEX EXT 100 Installation Guide - Dutch - 57 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info