652329
16
Zoom out
Zoom in
Previous page
1/32
Next page
16
2
1
5
5
6
6
3
4
11
4
11
1
6
7
8
9
2
10
12
13
5
3
14
15
ELLPREX 170÷630
fig. 19
and connect the mains, the burner, the
pump(s) and any ancillary equipment to
the panel board.
Close the panel board.
Guide the burner plug through the side
cable clamp plate (11) on the preferred
side and clamp the cable using the cable
clamp supplied.
Fix the side cable clamp plates (11) to the
casing side panels (3 & 4).
Fit the cables, leaving the boiler from the
back side, with the plastic screws of the
cable clamps (9).
G. Position the upper panels (12 and 13) and
press them against the side panels.
H. Remove the protective paper film from
data plate and ventilation requirement label
(14) and fit them at the top front corner of
the most accessible side panel after removal
of dust from the surface.
The data plate and label are in the
documents envelope.
Assembly of the casing should be carried out
in the following steps:
Refer to diagram on fig. 19 for details
A. Fit the insulation blanket (1) onto the boiler
shell and secure it in to place using the
elasticated straps (2) provided, ensuring
that the metal clips grip in to the external
surface of the insulation.
B. Locate the side panels (3) and (4) with
the lower bend inside the bottom L profiles
and the upper bend in the seats of front
and rear tube plates.
To determine which is the left and right
panel ensure that the cable clamp plates
are positioned facing toward the front
edge.
C. Open the combustion chamber door and
fit the front insulation (5), inserting the
hinges in the pre-cuts.
Insert the side ends of the insulation under
the bend of the two side panels (3 & 4).
D. Fit the rear insulation (pos. 6), fix the rear
lower, intermediate and upper panels (pos.
7, 15 & 8) with the self tapping screws.
Fit the plastic cable clamps (9) to the
upper rear panel (8).
E. After removal of the two side screws from
the panel board rotate its cover
towards the front and insert the cables and
the capillaries of thermometer and
thermostats through the slots on its base.
Fit the panel board to front upper panel (10).
Fit the upper panel (10), complete with the
panel board to the side panels (3 & 4).
F) Insert the thermometer and thermostat
bulbs in the bulb holders as shown in fig. 20
fig. 20
1 Thermometer bulb
2 Working thermostat bulb
3 Safety thermostat bulb
4 Minimum thermostat bulb
5 Bulb retaining clip
6 Contact spring
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Unical Ellprex at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Unical Ellprex in the language / languages: English as an attachment in your email.

The manual is 0,75 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info