167854
8
Zoom out
Zoom in
Previous page
1/36
Next page
Getting the most out of your amplifier is our goal. Having a subsonic filter in your subwoofer amplifier is
going to achieve just that. If you’re running a ported subwoofer system, it’s crucial that the signal from your
amplifier doesn’t drop drastically below the tuning frequency. If that should happen, your subwoofer will
feel as if it’s in open air, and that the enclosure does not exist. The result, slow and permanent damage to the
voice coil.
Our subsonic filter is always on to protect your subwoofers. With a minimum setting of 20Hz, and selectable
for 30 and 40Hz, your ensured that sub-harmonics are dropped off quickly. With most ports tuned in the
30-40Hz range, you can rest assured that your subwoofer will play cleaner and with less distortion.
Furthermore, your amplifier runs more efficient by not wasting voltage and current on reproducing these
frequencies.
Subsonic Filter
8
Nothing is more critical to an amplifier than the power delivery system, and dissipating heat as quickly as
possible. Your amplifier has been outfitted with circuitry to monitor both voltage and temperature through
top-mount digital meters. Voltage is crucial in ensuring that a sufficient amount of current is reaching your
amplifier. Having the proper gauge power wire and accessories will minimize your voltage loss. Using a high
power capacitor will help maintain voltage levels during transient peaks in your music.
Amplifiers will generate heat, and heat is it’s biggest enemy. Choosing a proper location for your amplifier
will ensure that it gets the cooling required to operate at a safe temperature rating. It is not recommended to
mount your amplifier upside down, in storage compartments or behind unventilated panels. Having the
ability to monitor the temperature on your amplifier is a bonus!
Voltage and Temperature Monitor
Many of today’s car audio systems will run multiple amplifiers. Using a Y-adapter is not a preferred way to
split your low level signal, as signal loss is guaranteed to happen. Your amplifier has been outfitted with a
pre-amp output circuit to pass on a full-range signal on to your next amplifier. If you require fading
capability between speakers, it will not be possible in this arrangement.
Low Level Output
Most head units today are outfitted with an amplifier “turn-on” circuit built in. Typically, the current
capability of this circuit is 500mA. While sufficient to activate one or two amplifiers, anything more than that
can require higher demands for current which it cannot handle. Our amplifiers have been outfitted with a
turn-on circuit of it’s own to assist you in your installation. Whether you’re running multiple amplifiers, have
additional processors or outboard processors, or use lighting effects in your installation, our +12v trigger
will help you turn them on. This output is limited to 1A and is internally protected with auto-reset circuitry.
Trigger Output
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ultimate t3 2050 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ultimate t3 2050 in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info