167856
6
Zoom out
Zoom in
Previous page
1/36
Next page
Ultimate recommends professional installation of all it’s products. Should you choose to install this product
yourself, please read this manual carefully and refer to the instructions detailed below. Failure to do so may
result in poor product performance, premature or immediate malfunction, and potential damage to your
vehicle or it’s contents.
Installation
When selecting a location to mount your amplifier, please ensure proper ventilation is considered. Areas below seats
or in trunks are suitable,so long as air flow is not restricted.Refrain from mounting your amplifier upside down,as heat
will not dissipate effectively, and can result in thermal shutdown or component failure
• Using a standard Allen key (3/32),remove the hex bolts located in the fins at the top of the amplifier heat sink.Pulling
the end caps away from the amp, you’ll find all the connectors and adjustments to complete the installation.
• Mount your amplifier using 4 screws,preferably onto a piece of wood. If screwing into the body of the vehicle,be sure
to check for brake, fuel or electrical lines,as well as stay clear of the gas tank.
Using a minimum of 8 gauge wire, run a power cable directly to the positive terminal of your battery to the ‘+12V’
terminal of your amp. A separate fuse must be located within 18 inches of the battery to protect the vehicle from a
potential short. Total up the fuse ratings on your amplifiers to determine the fuse size required under the hood.
Your amplifier will turn on only when ignition is activated.This can be accomplished by connecting an 18 gauge wire
to the ‘trigger’output on your head unit.If you are using an OEM radio,this will not be available. You must locate a +12v
switched circuit to achieve this.
The ground path is equally important to the positive feed of your amplifier. Find or create a bare metal spot on the
vehicles chassis. Using as short a wire as possible, connect to the GND’ terminal using the same gauge wire as you did
for power.The paint on the body must be removed to bare metal.
If you’re using a low-level output signal from your head unit, ensure to use a high quality RCA cable to prevent
unwanted noise.It is preferred to use the side opposite to the power wire to run the RCA.Failure to do so can introduce
unwanted noise into the input signal which will be heard through your speakers.
• If your head unit doesn’t have RCA,then the hi-level input of the amp would be used.For this, it is ideal to tap in on the
speakers closest to the amplifier location. Using regular 18 gauge speaker wire, take left and right (both positive and
negative) signals. Connect directly to the hi-level’ input on your amplifier. Proper gain settings are required to ensure
undistorted sound.
You have now completed the basic installation portion of your new amplifier. Please continue to the Amplifier
Settings” section of this manual to properly configure your amp for maximum listening pleasure.
6
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ultimate t3 1250 mono at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ultimate t3 1250 mono in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info