167853
6
Zoom out
Zoom in
Previous page
1/28
Next page
Ultimate recommends professional installation of all it’s products. Should you choose to install this product
yourself, please read this manual carefully and refer to the instructions detailed below. Failure to do so may
result in poor product performance, premature or immediate malfunction, and potential damage to your
vehicle or it’s contents.
Installation
When selecting a location to mount your amplifier,please ensure proper ventilation is considered. Areas
below seats or in trunks are suitable, so long as air flow is not restricted. Refrain from mounting your
amplifier upside down, as heat will not dissipate effectively, and can result in thermal shutdown or
component failure
Using a standard Allen key (3/32), remove the hex bolts located in the fins at the top of the amplifier heat
sink. Pulling the end caps away from the amp, you’ll find all the connectors and adjustments to complete
the installation.
Mount your amplifier using 4 screws, preferably onto a piece of wood. If screwing into the body of the
vehicle, be sure to check for brake, fuel or electrical lines, as well as stay clear of the gas tank.
Using a minimum of 8 gauge wire, run a power cable directly to the positive terminal of your battery to
the ‘+12V’terminal of your amp.A separate fuse must be located within 18 inches of the battery to protect
the vehicle from a potential short. Total up the fuse ratings on your amplifiers to determine the fuse size
required under the hood.
Your amplifier will turn on only when ignition is activated.This can be accomplished by connecting an 18
gauge wire to the ‘trigger’ output on your head unit. If you are using an OEM radio, this will not be
available.You must locate a +12v switched circuit to achieve this.
The ground path is equally important to the positive feed of your amplifier. Find or create a bare metal
spot on the vehicle’s chassis. Using as short a wire as possible, connect to the GND’ terminal using the
same gauge wire as you did for power.The paint on the body must be removed to bare metal.
If you’re using a low-level output signal from your head unit, ensure to use a high quality RCA cable to
prevent unwanted noise.It is preferred to use the side opposite to the power wire to run the RCA.Failure to
do so can introduce unwanted noise into the input signal which will be heard through your speakers.
• If your head unit doesn’t have RCA,then the hi-level input of the amp would be used.For this,it is ideal to
tap in on the speakers closest to the amplifier location.Using regular 18 gauge speaker wire,take left and
right (both positive and negative) signals. Connect directly to the ‘hi-level’ input on your amplifier. Proper
gain settings are required to ensure undistorted sound.
You have now completed the basic installation portion of your new amplifier. Please continue to the
Amplifier Settings” section of this manual to properly configure your amp for maximum listening pleasure.
6
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ultimate t2 1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ultimate t2 1200 in the language / languages: English as an attachment in your email.

The manual is 0,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info