167852
7
Zoom out
Zoom in
Previous page
1/36
Next page
The gain control (input sensitivity) on this amp is not a volume control. It is designed to provide proper
matching of various source units to this amplifier, and provides a reference to how much signal will be
necessary to reach maximum operating power. Correct settings will ensure safe operation for both your
amplifier and speakers.
Amplifier Settings
7
• Start by turning the gain level to the “8 volt setting. This is the minimum level, far left.
Next,turn up your head unit volume up to 75% of max volume.For example,if your digital volume control goes to “50”,
you would use the “40” level for this exercise.
Last,slowly begin increasing the gain until distortion becomes audible,then turn the gain back a notch.You have now
properly set your input sensitivity.
Your amplifier has been designed with an onboard 18db/oct crossover, or filter management system. How
you configure these settings will be dependent on the speakers you are connecting to the amp. The crossover
circuit consists of two main settings: 1. Filter Type; 2. Frequency Adjustment.
The “filter type” is controlled by a “LPF, FULL, HPF” switch. The low-pass filter, LPF, will allow only low
frequency information to pass on to the speakers. The opposite would be achieved using the HPF, high pass
filter. When no filter is required, the FULL setting would be selected, allowing all frequencies to pass.
For proper operation of some speakers, it is necessary to select the crossover point to which they will play.
The “frequency adjustment” setting allows you to accomplish this. In a LPF mode, only frequencies up to the
crossover point will play, with a gentle roll-off beyond that point. In HPF mode, any frequency above that
point will be heard, with those below being filtered away gradually.
Crossover Control
Sometimes, we want a little more kick to our system’s bottom end. Your amplifier has been outfitted with an
internal circuit to provide a boost at frequencies surrounding 45hz. A bass boost should be treated similar to
a gain control. Proper adjustment of this setting will be required to ensure safe operation of your amplifier
and speakers. When boosting the lower frequencies, turning the input sensitivity down would be required.
Failure to do so may result in permanent damage.
Bass Boost
Let’s face it, bass levels can fluctuate considerably from one style of music to another. Having some control
within reach enhances your level of listening pleasure. The RVC (not available on T3-2050), provides 18
steps of adjustment to fine tune your bass. Additionally, it provides essential monitoring of your amplifier.
Should the amplifier begin to clip, the letter “C” will appear in the display and begin to flash. Continuous
clipping will bring the “C” to a solid state. Clipping is the #1 reason for premature failure of your speakers or
subwoofers. If your voltage drops below 11v, the display will read “888”. If the fuse should blow, the display
will flash “---“.
Remote Volume Control
T3-Series
(sold separately)
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ultimate t 3 4075 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ultimate t 3 4075 in the language / languages: English as an attachment in your email.

The manual is 2,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info