647785
7
Zoom out
Zoom in
Previous page
1/52
Next page
4
ULGD 3.8 A1
GB
DANGER OF CHEMICAL
BURNS!
Wear protective glasses! Wear
protective gloves! If eyes or skin has
come into contact with battery acid,
rinse the affected body region off
with a large amount of clean water
and consult a doctor straight away!
Avoid causing a short circuit when
connecting the charger to the bat-
tery. Connect the negative pole
connector cable only to the nega-
tive battery or to the body work.
Connect the positive pole connector
cable only to the plus pole of the
battery!
Do not place the charger close to fire,
heat or to places with long-term expo-
sure to temperatures over 50 °C!
Ensure that no fuel lines,electric
cables, hydraulic or water pipes
are damaged by the screws during
assembly of the charger!
Do not cover the charger with any
objects!
Protect the electrical contact sur-
faces of the battery from short
circuiting!
Only use the charger for charging
and for charge retention of 6 V / 12
V lead batteries.
Do not charge frozen batteries.
Operation
Before use
Before connecting the charger, the operating
instructions must be observed.
Furthermore, the instructions of the vehicle man-
ufacturer regarding a permanently connected
vehicle battery must be observed. Secure the
vehicle, switch off the ignition.
Clean the battery poles. Take care that while doing
so, your eyes do not come into contact with the dirt.
Ensure sufficient ventilation.
Connecting
NOTES
There are two options for connecting the charger.
Connect the negative terminal connecting cable
(black) either directly to the negative terminal of
the battery or to the bodywork. Please also bear
in mind the vehicle manufacturer’s instructions.
Before starting the charging or trickle charging
procedure on a permanently installed battery in
a vehicle, first disconnect the negative terminal
connecting cable (black) of the vehicle from the
negative terminal of the battery. The negative
terminal of the battery is usually connected to
the vehicle’s coachwork.
Connect the positive pole clamp (red)
of the
charger to the positive pole of the battery.
Connect the negative pole clamp (black)
to the
negative pole of the battery or to the bodywork.
Connect the mains cable of the charger to
the mains socket.
The battery voltage display shows the cur-
rent battery voltage.
Should the connection of the clamps be swapped,
the LED „reverse connection“
lights up.
Disconnect
Disconnect the appliance from the mains supply.
Remove the negative pole clamp (black)
from the negative pole of the battery or from the
bodywork.
Remove the positive pole clamp (red) from
the positive pole of the battery.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ultimate speed ULGD 3.8 A1 - IAN 270075 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ultimate speed ULGD 3.8 A1 - IAN 270075 in the language / languages: English, German, Dutch, Danish, Swedish, Finnish as an attachment in your email.

The manual is 0,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info