485270

Turmix A31122 Manual

21
Zoom out
Zoom in
Previous page
1/28
Next page
20
21
20
DE
FR
DE
IT
GB
Overview
1. Driving unit with rubber handle
2. Immersion mixer
– Attach mixer from below onto the driving unit.
– Insert the immersion mixer on the driving unit
turning it until it clicks.
– The mixer may not be used directly in pots.
3. On/off switch
It works only if the safety button is pressed (4).
– To switch on the appliance keep the switch
pressed down (if you release it, the mixer will turn
off automatically for safety reasons).
–
If the appliance is turned on when the battery
charger is down, a safety device automatically
turns it off. The LED display starts flashing (5).
After it turns off automatically, do not press down
on the On/Off button (3), otherwise the accumula-
tor might be damaged.
4. Safety button
The safety button avoids that one accidentally turns
on the appliance.
– To turn the appliance ON, press down on the safe-
ty button and the On/Off switch (3). While the mix-
er is working one can release the safety button.
5. Battery Charger - Led Display
While the appliance is being used, the battery charge
status is displayed by the LED (the appliance is not
connected to the battery charger):
– press the safety button (4.)
–
LED is lit = Battery full
–
LED flashes slowly = Battery half fulll
–
LED flashes quickly = Battery almost empty
–
Before using the appliance for the first time, fully
charge the base unit (approx. 2 hours).
6. Blending cup with lid
– Place the cup on a flat surface.
– To avoid spurts, immerge mixer completely before
pressing down on the ON button.
– For better results blend small portions.
– To preserve in the fridge apply the lid onto the
blending cup.
7. After use
– First draw out the immersion mixer.
– Remove the mixer for cleaning (be careful because
the blade is very sharp; hold it only by its plastic
handle).
–
Insert the battery charger into the socket (do not
use any other battery charger!).
–
Position the driving unit on the special support.
Keep all contacts clean.
8. Battery charge status:
– LED goes out after approx. 10 seconds. = battery
full.
–
LED on = battery is charging.
–
If you don’t use the appliance for a long time,
unplug the battery charger.
Assembly
– The charging station can be placed on a flat surface
or mounted on a wall with the screws contained in
the box (not, however, over sinks, stoves or plugs).
9.-12. Assembly
– Unpack screws and screw anchors.
– Mark the holes on the wall (extract by pulling
down the assembly plate from the charging station
and use it like a template). Do not assemble over
kitchen sinks, stoves or current sockets.
– Drill creating two holes (6 mm in diameter).
– Insert screw anchors and fix the plate with the
screws ( with pins in the upward position).
– Insert the charging station from above (it clicks).
– Insert the battery charger into the socket (the
remaining cord can be wound around the two pins
of the assembly plate).
– Position the driving unit onto the special support
on the left.
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Turmix A31122 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Turmix A31122 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 9,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info