804599

Turbionaire Senso 20 - Wifi Manual

12
Zoom out
Zoom in
Previous page
1/112
Next page
12
lights up and the default fan speed is high, and the default humidity is 50%. In the
power-on state, press the power button to turn off, the running indicator light goes off and
the compressor stops immediately, and then the fan shut down after 30 seconds delay.
MODE
Auto mode - Continuously drying mode – Sleeping mode cycle, press once to
switch the mode from one to another, the corresponding indicator lights up.
•Auto mode: when environmental humidity ≥ set humidity +3%, the fan starts working
and compressor starts working after 3 seconds. When environmental humidity ≤ set
humidity -3%, the compressor stops working and fan stops working after 30 seconds’
delay. Both fan speed and humidity can be adjusted under auto mode.
•Continuously drying mode: The machine continues to run, but the humidity cannot be
adjusted.
SLEEP/ RESET:
Touch the sleep button, the button lights up and start the sleep function. If the
control panel is not operated within 10 seconds, all indicators turns dark gradually and
the fun speed is automatically switched from high to low. Touch any button to
wake up the SLEEP Mode indicator. Touch MODE button again to exit the SLEEP mode.
Long press the SLEEP button to start the filter reset function (RESET).
ATTENTION Hold down the RESET button for more than 5 seconds if the dehumidifier
does not respond to any commands! This means that the dust filter remider has been
activated and this action is required to reactivate the dehumidifier functions.
NOTE:
When environmental humidity ≤ 57%，compressor stops working and the fan shut down
after 30 seconds’ delay.
When environmental humidity ≥ 63%，the fan starts working and compressor starts
working after 3 seconds.
Fan speed and humidity cannot be adjusted under SLEEP mode.
TIMER
Press the timer button to set the 0-12 hour timing function. The interval is 1 hour.
Each time you press this button, the value increased 1 hours and then the corresponding
timing value is displayed on the screen. The setting value is “00” to cancel the timer
function. The indicator turns out. After the timer is set and completed, the timer LED is on
during the timing period. After the timing is over, the timer LED turns off automatically.
In the running state, set the time to turn off the machine;
In the standby state, set the time to turn on the machine.
HUMIDITY SET
Touch the humidity button (HUM SET) to check the current environment humidity,
touch this button again and you can set the humidity. The range of target humidity is 30%-
35% - 40% - 45% - 50% - 55%- 60% - 65% -70% - 75%- 80%. After setting 3 seconds,
the system confirms the input value and then the machine exits the setting state, and
returns the current humidity. In the drying mode, the target humidity cannot be changed.
POWER
In the standby state, press the power button to turn on, the operation indicator
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Turbionaire Senso 20 - Wifi at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Turbionaire Senso 20 - Wifi in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 8.15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info