736479

Tunturi T85 Treadmill - 2020 Manual

25
Zoom out
Zoom in
Previous page
1/112
Next page
25
English
The warranty does not cover sounds or noises emitted during use
where these do not substantially impede the use of the equipment
and where they are not caused by a fault in the equipment.
The warranty does not cover defects arising from the failure to
carry periodic maintenance as outlined within the Owner’s Manual
for the product. Furthermore, the warranty does not cover defects
arising from usage and storage within an unsuitable environment
as described within the Owner’s Manual which should be indoors,
dry, dust and grit free and within a temperature range of +15°C to
+35°C. The warranty does not cover maintenance activities, such as
cleaning, lubricating, and normal part adjustments, nor installation
procedures that customers can accomplish themselves, such as
changing uncomplicated meters, pedals and other similar parts not
requiring any dismantling/reassembling of the fitness equipment.
Warranty repairs carried out by other than authorised Tunturi
representatives are not covered.
Failure to follow the instructions given in the Owner’s Manual will
invalidate the product’s warranty.
Cleaning and maintenance
⚠ WARNING
• Before cleaning and maintenance, remove the mains plug from
the wall socket.
• Do not use solvents to clean the equipment.
- Do not block the ventilation openings. Keep the ventilation
openings clear from dust, dirt and other obstructions.
- Clean the equipment with a soft, absorbent cloth after each use.
- Clean the visible parts of the equipment with a vacuum cleaner
with a small suction nozzle
- Regularly check that all screws and nuts are tight.
Belt and Running Deck
Your treadmill uses a very high-efficient low-friction bed. Performance
is maximized when the running deck is kept as clean as possible.
Use a soft, damp cloth or paper towel to wipe the edge of the belt
and the area between the belt edge and frame. Also reach as far
as practical directly under the belt edge. This should be done once
a month to extend belt and running deck life. Use water only - no
cleaners or abrasives. A mild soap and water solution along with a
nylon scrub brush will clean the top of the textured belt. Allow the
belt to dry before using.
Lubrication (fig. F-4)
The running belt must be checked for lubrication condition regularly.
⚠ WARNING
• Before lubrication, remove the mains plug from the wall socket.
⚠ CAUTION
• We recommend to check the running belt lubrication at least
once every month, as more factors than time can be effective to
the lubricant conditions.
• Only lubricate the running belt if necessary. If you apply too
much lubricant, the running belt will slip easily due to lack of
friction.
- Stand steadily on the running belt.
- Take hold of the front handlebar and push the running belt with
your feet so that it slides back and forth. The running belt must
move smoothly and evenly without making sound.
- If the running belt does not move smoothly and evenly or if the
running belt does not move at all, touch the underside of the
running belt with your fingertips to check the lubrication:
• If you feel lubrication or your fingertips are shiny, there is
sufficient lubrication on the running belt.
• If you do not feel lubrication or your fingertips are dusty or
rough, apply lubricant (15-20 ml) in the middle of the running
deck under the running belt and let the equipment operate at
5km/h for at least 5 minutes.
• After lubrication, do not fold the equipment before having done
a workout for 20 minutes with a speed of at least 5 km/h. The
lubricant will be spread evenly over the running belt.
Belt Dust
This occurs during normal break-in or until the belt stabilizes. Wiping
excess off with a damp cloth will minimize build-up.
General Cleaning
Dirt, dust, and pet hair can block air inlets and accumulate on the
running belt. On a monthly basis: vacuum underneath your treadmill
to prevent buildup. Twice a year, you should remove the black motor
hood and vacuum out dirt that may accumulate.
UNPLUG POWER CORD BEFORE THIS TASK.
Belt adjustments
Adjustment must be made from the rear roller. The adjustment bolts
are located at the end of the step rails in the end caps.
- Tighten the rear roller bolts (clockwise) only enough to prevent
slippage at the front roller. Turn both running belt tension
adjustment bolts in increments of 1/4 turn each and inspect for
proper tension by walking on the belt at a low speed, making sure
the belt does not slip. Keep tensioning the bolts until the belt
stops slipping.
- If you feel the belt is tight enough, but it still slips, the problem
may be a loose Motor drive belt under the front cover.
- Do Not Over-tighten
Over tightening will cause belt damage and premature bearing
failure.
Running belt tracking adjustment
The performance of your treadmill is dependent on the frame running
on a reasonably level surface. If the frame is not level, the front and
back roller cannot run parallel, and constant belt adjustment may be
necessary.
The treadmill is designed to keep the running belt reasonably
centered while in use. It is normal for some belts to drift near one
side while the belt is running with no one on it. After a few minutes
of use, the running belt should have a tendency to center itself. If,
during use, the belt continues to move toward one side, adjustments
are necessary.
EXCEPTION:
During rehabilitation where the user is using one leg much stronger
than the other, it might happen that the running belt drifts to one
side. In these cases you should not adjust unless the running belt
does not centre itself during normal condition usage.
To set running belt tracking (fig. F-5)
A 10 mm Allen wrench is provided to adjust the rear roller. Make
tracking adjustments from the left side only. Set belt speed at
approximately 3 to 5 kph.
Remember, a small adjustment can make a dramatic difference!
Turn the bolt clockwise to move the belt to the right.
Counterclockwise to move to the left. Turn the bolt only a 1/4 turn
and wait a few minutes for the belt to adjust itself. Continue to make
1/4 rotation turns until the belt stabilizes in the center of the running
deck.
The belt may require periodic tracking adjustment depending on use
and walking/running characteristics. Some users will affect tracking
differently. Expect to make adjustments as required to center the
tread-belt. Adjustments will become less of a maintenance concern
… 25 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tunturi T85 Treadmill - 2020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tunturi T85 Treadmill - 2020 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 9,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info