738064

Tunturi Star Fit B100 Manual

18
Zoom out
Zoom in
Previous page
1/52
Next page
18
English
- Press and hold START/ STOP key for over 2 seconds
to reset console and to go back to main menu.
(Active training data will be lost )
H.R.C. mode. (Program 12)
- Use UP/ DOWN key to select Program 12 and press
ENTER to confirm.
- Use UP/ DOWN key to set TIME,
Range: 0:00 - 1:00 ~ 99:00 ±1:00
confirm setting by pressing ENTER.
- Use UP/ DOWN key to set DISTANCE,
Range: 00.00 - 00.10 ~ 99.90 ± 00.10
confirm setting by pressing ENTER.
- Use UP/ DOWN key to set CALORIES,
Range: 0.0 - 1.0 ~ 999.0 ± 1.0
confirm setting by pressing ENTER.
- Use UP/ DOWN key to set PULSE limit
Range: 0 - 60 ~ 220 ± 1
confirm setting by pressing ENTER.
NOTE
• When setting more than one goal, the training
will end at first achieved goal.
• Continue the workout by pressing START/ STOP
button, and training will end again at first next
achieved goal.
• Leave a goal blank and it will not be seen as a
pre-set limit.
• Set Pulse limit is resistance control function,
Resistance will auto lower when value is over
pulse target, and auto upper when under pulse
target.
- Press START/ STOP key to start workout
- Use UP/ DOWN key to adjust resistance level.
Load level is shown in LEVEL window.
- Press START/ STOP key to pause workout.
- Press and hold START/ STOP key for over 2 seconds
to reset console and to go back to main menu.
(Active training data will be lost )
Recovery
- The RECOVERY key will only be valid if pulse is
detected.
- TIME will show „0:60“ (seconds) and counts down
to 0.
- Computer will show F1 to F6 after the countdown
to test heart rate recovery status. User can find the
heart rate recovery level based on the chart below.
- Press RECOVERY key again to return to the
beginning.
F1 Outstanding
F2 Excellent
F3 Good
F4 Fair
F5 Below average
F6 Poor
Trouble shooting:
- If there is no signal when you pedal, please check if
the cable is well connected.
NOTE
• When stop training for 4 minutes, the main
screen will be off.
• If the computer displays abnormally, please re-
install the transformer and try again.
Cleaning and maintenance
The equipment does not require special maintenance.
The equipment does not require recalibration when
it is assembled, used and serviced according to the
instructions.
WARNING
• Do not use solvents to clean the equipment.
• Clean the equipment with a soft, absorbent cloth
after each use.
• Regularly check that all screws and nuts
are tight.
• If necessary, lubricate the joints.
Defects and malfunctions
Despite continuous quality control, defects and
malfunctions caused by individual parts can occur in the
equipment. In most cases, it will be sufficient to replace
the defective part.
- If the equipment does not function properly,
immediately contact the dealer.
- Provide the model number and the serial number of
the equipment to the dealer. State the nature of the
problem, conditions of use and purchase date.
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tunturi Star Fit B100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tunturi Star Fit B100 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info