736353

Tunturi FitRace 40 HR Manual

16
Zoom out
Zoom in
Previous page
1/40
Next page
16
English
NOTE
• The console switches to standby mode when the
equipment is not used for 4 minutes.
Explanation Display functions
RPM
Display the rotations per minute.
Range: 0 ~ 999 RPM.
Without any signal being transmitted into the monitor
for 4 seconds during workout, RPM will display “0”
Time
Automatically accumulates workout time when
exercising.
Display range: 00:00 ~ 99:59.
Speed
Displays current training speed.
Range 0.0 ~ 99.9 / Units: KM/H.
Without any signal being transmitted into the monitor
for 4 seconds during workout, RPM will display “0”.
Distance
Automatically accumulates the distance from exercise
when exercising.
Range 0.0 ~ 999.9 / Units: KM.
Calories
Automatically accumulates calories burnt when
exercising.
Range: 0 ~ 9999 / Units: K.Cal.
NOTE
• This data is a rough guide for comparison of
different exercise sessions which cannot be used
in medical treatment
Pulse
- Current pulse will display after 6 seconds when
detected by the console.
- Without any pulse signal for 6 seconds, console will
display “P”.
- Pulse alarm will sound when current pulse is over
the target pulse.
- Range: 0-30 ~ 230 BPM.
Explanation of buttons
Mode/ Reset
- Press Mode/ Reset button to select console
functions.
- Push and hold for 3 seconds in, stop Mode/ Reset,
to reset: Time, Distance, Calories.
Opperation
Power on
- Press any key to power on the console when being
in sleep mode..
- Start pedalling to power on the console when being
in sleep mode.
Power off
Without any signal being transmitted into the monitor
for 4 minutes the monitor will enter SLEEP mode
automatically. ( Active training data will be lost )
Workout setting
- Press MODE/ RESET key to select the function of
TIME, DISTANCE, CALORIES, and PULSE. Use SET
key for setting and press MODE/ RESET key for
confirmation.
- For instance the time set-up, when the time value
is blinking, you can use UP and DOWN (DIAL) to
adjust the number. Press SET key for confirmation
and skip to next set-up. The set-up of DISTANCE,
CALORIES and PULSE is the same as TIME set-up.
- Once the workout begins and the console picks up
the exercise signal, the value of SPEED, RPM, TIME,
DISTANCE and CALORIES will count up on the
display.
- If a target is set for a specific value, that value will
countdown, till target is reached.
Cleaning and maintenance
The equipment does not require special maintenance.
The equipment does not require recalibration when
it is assembled, used and serviced according to the
instructions.
WARNING
• Do not use solvents to clean the equipment.
• Clean the equipment with a soft, absorbent cloth
after each use.
• Regularly check that all screws and nuts
are tight.
• If necessary, lubricate the joints.
Defects and malfunctions
Despite continuous quality control, defects and
malfunctions caused by individual parts can occur in the
equipment. In most cases, it will be sufficient to replace
the defective part.
- If the equipment does not function properly,
immediately contact the dealer.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Tunturi FitRace 40 HR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Tunturi FitRace 40 HR in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,56 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info