Manual Tunturi FitCycle 30 (page 17 of 48) (English, German, Dutch, French)

738068

Zoom out

Zoom in

1/48

English

Remark: During the process of pulse measurement,

because of the contact jamming, the measurement

value may be higher than the virtual pulse rate during

the first 2~3 seconds, then will return to normal level.

The measurement value cannot be regarded as the

basis of medical treatment.

NOTE

• If the display is faint or shows no figures, please

replace the batteries.

• The monitor will automatically shut in standby

mode if there is no signal received after 4

minutes.

• The monitor will be auto-powered on when

starting to exercise or at the push of a button.

• The monitor will automatically start calculating

when you start to exercise and will stop

calculating when you stop exercising for 4

seconds.

Specifications:

Function

- Auto scan Every 4 seconds

- Time 0:00 ~ 99:59

- Current speed The maximum speed to be

displayed is 99,9 KM/H

- Trip Distance 0.00 ~ 99.99 KM

- Calories 0.0 ~ 999.9 K.Cal

- ODO 0.1 ~ 999.9 KM

- Pulse rate 40 ~ 240 BPM

Operating Temperature 0°C ~ +40°C

Storage Temperature -10°C ~ +60°C

Extra notes

- If the display is faint or shows no figures, please

replace the batteries.

- The monitor will automatically shut off if there is no

signal received after 4 minutes .

- The monitor will be auto-powered on when starting

to exercise push button w/signal in.

- The monitor will automatically start calculating

when you start to exercise and will stop calculating

when you stop exercising for 4 seconds .

Cleaning and maintenance

The equipment does not require special maintenance.

The equipment does not require recalibration when

it is assembled, used and serviced according to the

instructions.

WARNING

• Do not use solvents to clean the equipment.

• Clean the equipment with a soft, absorbent cloth

after each use.

• Regularly check that all screws and nuts

are tight.

• If necessary, lubricate the joints.

Defects and malfunctions

Despite continuous quality control, defects and

malfunctions caused by individual parts can occur in the

equipment. In most cases, it will be sufficient to replace

the defective part.

- If the equipment does not function properly,

immediately contact the dealer.

- Provide the model number and the serial number of

the equipment to the dealer. State the nature of the

problem, conditions of use and purchase date.

Transport and storage

WARNING

• Carry and move the equipment with at least two

persons.

• Remain standing in front of the equipment

on each side and take a sturdy grip at the

handlebars. Tilt the front of the equipment

so as to lift the rear of the equipment on the

wheels. Move the equipment and carefully put

the equipment down. Place the equipment on a

protective base to prevent damage to the floor

surface.

• Move the equipment carefully over uneven

surfaces. Do not move the equipment upstairs

using the wheels, but carry the equipment by the

handlebars.

• Store the equipment in a dry place with as little

temperature variation as possible.

Additional information

Packaging disposal

Government guidelines ask that we reduce the amount

of waste material disposed of in land fill sites. We

therefore ask that you dispose of all packaging waste

responsibly at public recycling centres.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Tunturi FitCycle 30 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,52 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Tunturi FitCycle 30 Manual

Product: