Manual Tunturi Classic loopband RUN 1.0 (page 7 of 70) (English, German, Dutch, French, Italian, Swedish, Spanish, Finnish)

542650

Zoom out

Zoom in

1/70

6 7

Run 1.0 - OWNER’S MANUAL ENGLISH

demanding use, the lubrication needs be checked at

shorter intervals. This is best done before you begin a

training session. Check the lubrication as follows:

1. Ensure the treadmill is powered off! Step on the treadmill

belt .and stand steadily where you normally run on the

belt.

2. Take hold of the horizontal handlebar and push the

belt with your feet so that it slides back and forth. The belt

should move softly and evenly, without a sound.

3. If you notice jerky movement or if the belt will not slide

check for lubrication by sliding your hand under the belt.

Lubricate the running deck according to the following

instructions:

1. Attach the nozzle of the lubrication tube to the T-Lube S

container.

2. Lift the running deck and lock it.

3. Position the nozzle between the belt and the board. Try

to reach the spray as far into the center of the running

deck as possible.

4. Spray the lubricant for 2-3 seconds.

5. Lower the running deck into its normal position. Use

treadmill for your training session. Or allow the treadmill to

run for at least 5 minutes.

NOTE! Lubricate your treadmill only with T-Lube S

silicon lubricant. Contact your local Tunturi distributor for

further supplies of T-Lube or further information on

lubrication and maintenance.

ALIGNING THE RUNNING BELT

Monitor belt tracking during exercise and make

adjustments as needed. The belt should run in the center

of the treadmill. Alignment is not usually needed, provided

• the treadmill is placed on an even, solid and

horizontal surface and the belt is correctly tensioned

• the alignment of the belt is correct It is, however,

possible for the belt to be pushed to one side due

to the user’s running style (e.g. more weight on one

foot). The alignment of the belt is adjusted by turning

the two bolts at the back of the treadmill.

ALIGN THE BELT ACCORDING TO THE FOLLOWING

INSTRUCTIONS:

1. Turn the power switch on and increase the treadmill’s

speed to 5 km/h (3 mph).

2. If the belt drifts to the left, turn the left adjustment bolt

1/4 turn clockwise and the right adjustment bolt 1/8 turn

anti-clockwise. If the belt drifts to the right, turn the right

adjustment bolt 1/4 turn clockwise and the left adjustment

bolt ¼ turn anti-clockwise.

3. If the belt remains centered the adjustment is correct.

If not, continue to make small adjustments as above

until the belt is correctly aligned. If the belt is allowed run

across to one side for long periods of time the edges of

the belt may be damaged and the treadmill may not

continue to operate correctly. Any damage to the belt

caused by the lack of necessary adjustment will not be

covered by the warranty.

ADJUSTING THE BELT TENSION

The belt must be tensioned if it begins to slip on the rollers.

In normal use, however, keep the belt as loose as possible!

The belt tension is adjusted by turning the same screws

as used for aligning the running belt. If turning the screws

will not effect the belt tension, please contact your local

Tunturi dealer.

1. Increase the treadmill’s speed to 5 km/h (3 mph).

2. Turn both adjustment screws an equal amount, ¼ turn

clockwise.

3. Try to slow the belt down by holding onto the handrails

and braking as you walk (as if you were walking downhill).

If the belt slips, turn another 1/4 turn and repeat the test.

When braking heavily the belt may slip. If the belt keeps

slipping despite repeated adjustments, please contact

your local Tunturi dealer.

MALFUNCTIONS

NOTE! Despite continuous quality control, defects

and malfunctions caused by individual components may

occur in the equipment. In most cases it’s unnecessary to

take the whole device in for repair, as it’s usually sufcient

to replace the defective part. Always give the model,

serial number of your equipment and in case of

malfunctions also conditions of use, nature of malfunction

and any error code.

When you encounter unusual behavior from the treadmill,

simply turn the power switch off, wait 1 minute and turn

the power switch on to reset the treadmill. This should

clear incidental errors and ready the treadmill for normal

operation again. If after you have reset the treadmill

by turning the power switch off and on again, and the

treadmill is still not operational, contact your local Tunturi

dealer for service.

If you require spare parts, always give the model, serial

number of your equipment and the spare part number for

the part you need. The spare part list is at the back of this

manual. Use only spare parts mentioned in the spare part

list.

ERROR CODES

The user interface will display information about

operational faults.

E1: Speed sensor error. Unplug the electrical cord from

the wall outlet and from the treadmill, wait 1 minute and

turn the power switch on again. If treadmill recovers to

normal operation, you may continue to use the treadmill.

Otherwise, call the dealer for service.

E3: Lift motor error. Unplug the electrical cord from the

wall outlet and from the treadmill, wait 1 minute and

turn the power switch on again. If treadmill recovers to

normal operation, you may continue to use the treadmill.

Otherwise, call the dealer for service.

PROTECTIVE CIRCUIT

The machine will shut off when the electricity load is

above the machine’s capacity. To restart the machine,

please follow the procedure below:

A. Unplug the power cord from the machine’s socket.

B. Push in the safety switch.

C. Replug the power cord into the machine’s socket.

Run1.0_MANUAL_120914.indd 7 9/14/2012 6:09:47 PM

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Tunturi Classic loopband RUN 1.0 in the language / languages: English, German, Dutch, French, Italian, Swedish, Spanish, Finnish as an attachment in your email.

The manual is 6,58 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Tunturi Classic loopband RUN 1.0 Manual

Product: