Manual TTulpe Indoor B-10 N25Eco (page 8 of 12) (English)

782470

Zoom out

Zoom in

1/12

When initially installing the device, qualified persons must

perform the following tests:

-Check that the internal and external parts of the gas supplying

device are sealed.

Check that the gas quantity supplied is equal to that required by

the device.

Check that the device receives the type of gas it is

manufactured to process.

Check that the gas supply pressure does not go beyond the

maximum pressure values displayed on the information plate.

- Check that the gas supply system supplies the necessary amoun

t of gas to the device and that it is equipped with all the

necessary safety devices prescribed by current regulations.

If the user is absent for a lengthy period, turn off the main gas

supply tap.

Do not obstruct the area s’ventilation openings where the device is

installed to avoid dangers such as the build-up of toxic and

explosive substances. Do not utilize gas tubes to earth electrical

devices. Water connection Connect the water heater to the

water supply and insert a tap to int ercept the water above the

device. From the front, the cold-water i nput is on the right and the

hot water output is on the left.

Insert the filter into the water valve input fitting.

Remove the plastic nut from the hot water output fit in before

connecting it to the water supply.

Check the water hardness (°f).

In case of high water hardness, we recommend

installing upstream of the appliance the water softener

device or oth er device in compliance with the regulations

including any re visions.

Ensure that the tubes of your water system are not used to

earth your electrical system or telephone, they are inappropriate

for p erforming this task.

In a short amount of time this can damage tubes and the device.

Disposal of waste product

This B11BS water heater is supplied with a device for releasing

flue gas.

For output of combustion by-products refer to the regulations in

force including any updates.

The gas devices with an attachment for a waste gas flue must be

connected directly to properly working chimney or flue pipe; only if

these devices are not present is it then permitted to release

gases directly outside.

The fitting of devices to a chimney or flue pipe must occur via a

smoke channel. Smoke channels must be connected to a

chimney or a smoke channel in the same or adjacent area to

where the device is installed and must be made of materials

resistant to mechanical strain, heat and the effects of combustion

by-product s and their condensation. The flue gas temperature

must always be above condensation temperature in all points of the

smoke chan nel regardless of external conditions.

FLUE GAS RELEASE SAFETY DEVICE

The product is equipped with a series of flue gas release safety

devices. The device ensures the correct release of combustion by -

products, the flow of combustible gas to the release conduit

and the smoke channel.

The safety device contains a “thermostat ,”it can stop the flow of

gas to the main burner and the pilot flame.

The safety device can be triggered by the partial or total obstruction

of the release conduit or the smoke channel.

Whenthe temperatureof thermostatresumeto normal,removethe fault

codeaccordingto the Fault Code Solution. Thenturnon the tap again.

If the device or its electrical connections breaks down, the product

cannot be put ON, it ensures a safe condition

If the device or its electrical connections breaks down, the machine

operation is blocked.

If the machine is constantly blocked because of the flue gas

safety device, it is necessary to request the assistance of a

qualified te chnician according

to law in force, to che

ck the correct releas

e of flue gas through

the release conduit

and/or the smoke ch

annel,ac-cording to

the installation regul

OPERATION

High water temperature

A-ON/OFFbutton

B-UP button

C-DOWN button

ation.

It is highly prohibited

to attempt to modify

or remove the flue g Fig.6

as safety device; thi

s risks the safety of

the user and persons in the area. Only a qualified technician who is

authorized by the manufacturer can meddle with the safety devic

e to check its functionality or to substitute it if necessary.

If it is necessary to replace the device, it is vital to only use “original

parts”supplied by the manufacturer since it has been designed,

studied, and regulated to be fitted with the water heater.

Fig.7Fig.8

Low water temperature

148.00 mm

210.00 mm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of TTulpe Indoor B-10 N25Eco in the language / languages: English as an attachment in your email.

The manual is 6.19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of TTulpe Indoor B-10 N25Eco

TTulpe Indoor B-10 N25Eco Usermanual and installation guide - German - 12 pages

TTulpe Indoor B-10 N25Eco Usermanual and installation guide - Dutch - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

TTulpe Indoor B-10 N25Eco Manual

Product: